manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 789 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 789

BRI-BD/LGATE-BD (ISDN-BRI Line Circuit Pack)

Issue 5  October 2002

789

555-233-119

BRI-BD/LGATE-BD (ISDN-BRI Line 
Circuit Pack)

NOTE:

Some of the information in this section is reserved for future use.

ISDN-BRI Line is a packet port circuit pack that provides access to ISDN-BRI 
endpoints. The ISDN-BRI Line circuit pack supports 12 ports, each of which 
provides access to ISDN stations. Voice and circuit-switched data from the ISDN 
stations are carried on the Time Division Multiplex (TDM) Bus. 

LEDS

The ISDN-BRI Line circuit pack performs extensive initialization tests and lights 
both the red and green LEDS during the initialization testing. See 

‘‘LED 

Interpretation’’

 in 

Chapter 1, ‘‘Maintenance for CSI systems’’

, for more details on 

circuit pack status LEDs.

MO Name 

(in Alarm Log)

Alarm Level

Initial Command to Run

1

1.

Where P is the port network number (1 for PPN); C is the carrier designation (A, B, or C); and SS is 
the address of the slot in the carrier where the circuit pack is located (01, 02, etc.).

Full Name of MO

BRI-BD

MAJOR

test board PCSS l

ISDN-BRI Line Circuit Pack

BRI-BD

MINOR

test board PCSS l

ISDN-BRI Line Circuit Pack

BRI-BD

WARNING

test board PCSS sh

ISDN-BRI Line Circuit Pack

LGATE-BD

MAJOR

test board PCSS l

DEFINITY Lan Gateway

LGATE-BD

MINOR

test board PCSS l

DEFINITY Lan Gateway

LGATE-BD

WARNING

test board PCSS sh

DEFINITY Lan Gateway

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов