manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1605 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1605

SYS-LINK (System Links)

Issue 5  October 2002

1605

555-233-119

Notes:

a. Error Type 13: indicates that the link went down. The link may have gone 

down or never come up. Enter command status sys-link location and 
check the value of the field 

Faulted Path

. If the value is 

default

, then 

the link never came up. If the value is 

present

, then the link came up and 

went down.

Follow the Common Procedure described above. Wait for 3 min before 
checking the link state. Repeat the procedure until there are no problems 
with the components. 

b. Error Type 257: indicates that the link has experienced uplink flow control. 

Manifest effect of this error is that the end-point may be hyperactive. The 
system link is alarmed if 4 or more errors of this type are detected within 10 
minutes.

To correct the problem, follow the Common Procedure described above. 
Clear errors and wait for 10 minutes.

c. Error Type 513: indicates that the link has experienced downlink flow 

control. Manifest effect of this error is that some information packets from 
the packet interface board have been lost. The link is reset on first 
occurrence, hence, Error 1025 will also be logged. The system link is 
alarmed if 2 or more errors of this type are detected within 10 minutes.

To correct the problem, follow the Common Procedure described above. 
Clear errors and wait for 10 minutes.

d. Error Type 772: indicates that the link experienced a temporary disconnect 

due to excessive resets or state transitions. The effect of this error is that 
the link is taken down and then brought up again. The system link is 
alarmed if 2 or more errors of this type are detected within 10 minutes.

To correct the problem, follow the Common Procedure described above. 
Clear errors and wait for 10 minutes.

e. Error Type 1025: This error indicates that the link has been reset. Manifest 

effect of this error is that information packets queued at the time of reset 
are been lost. The system link is alarmed if 20 or more errors of this type 
are detected within 10 minutes.

To correct the problem, follow the Common Procedure described above. 
Clear errors and wait for 10 minutes.

1537 (g)

WARNING

OFF

test sys-link PCSSpp l cl

1793 (h)

WARNING

OFF

test sys-link PCSSpp l cl

2049 (i)

WARNING

OFF

test sys-link PCSSpp l cl

Table 462.

SYS-LINK Error Log Entries  — 

Continued

  

Error 

Type

Aux 

Data

Associated Test

Alarm 

Level

On/Off 

Board

Test to Clear Value

Continued on next page

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов