manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 347 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 347

list trace

Issue 5  October 2002

347

555-233-119 

list trace ras

Use list trace ras to see the registration, admission, and status messages in 
H.225 used between two H.323 entities for gatekeeper discovery and endpoint 
registration. This information is helpful when an endpoint fails to register. For 
example, use list trace ras for a particular endpoint, then register the endpoint. If 
no commands show up on the output screen, the gatekeeper is not receiving the 
message from the endpoint. Check for a network problem.

■

list trace ras ip-address x.x.x.x. displays RAS messages between the 
gatekeeper from which this command is run and endpoints, using the IP 
address specified in the command

■

list trace ras ip-stations x displays RAS messages between the 
gatekeeper and endpoints using the extensions specified in the command

■

list trace ras forced_urqs displays some RAS unregistration request 
(URQ) messages sent by the gatekeeper to force unregister endpoints. Not 
all gatekeeper-originated URQ messages are captured here. See the 
denial event log (‘display events’, Category = denial) for a complete record. 

list trace station

Use list trace station to check the VPI.VCI data for a specified station (list trace 
station extension). This command traces calls to and from the station, listing the 
calling name and number, call redirection reason, coverage path, and call routing 
data. Denial events appear for calls that receive intercept or re-order. 

The command syntax for ATM-specific trace data is:

list trace station xxxxx/a where xxxxx is the station number, and /a 
means that you are requesting ATM-specific data.

Screen 62

 shows VPI.VCI data for a successful 2-party call setup. Use 

Field 

descriptions (list trace)

 to interpret this report.

Screen 62.

List trace station 

list trace station 52501/a

Page 1 of 1

SPE B

LIST TRACE

Time Data

15:12:07 

Calling party station 

57405 cid 0x20

15:12:09 dial 

52501

15:12:09 

ring station 52501 cid 0x20

15:12:09 

ATM setup PN01-0081 to PN03-0045

15:12:09 

ATM setup PN03-0046 to PN01-0082

15:12:11 

active station 52501 cid 0x20

15:12:22 

idle station 57405 cid 0x20

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов