Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1929

Страница: 1929 / 1930

Index

Issue 5 October 2002

1929

555-233-119

tests and audits, (continued)

#36 Station Status and Translation Audits and

Updates

649

1550

#36 Station Status and Translation Audits and Updates

Test

665

#40 Tone Generator Transmission Test

1732

#42 Tone Detection Verification Test

893

#46 Clock Health Inquiry Test

1727

#47 Loop Around and Conference Test

667

#48 Station Present Test

651

672

1551

#50 NPE Connection Audit Test

1080

1365

1778

#52 Control Channel Loop Around Test

1081

1271

1366

1378

1779

#52 Control Channel Loop-Around Test

746

883

#53 SAKI Sanity Test

1082

1272

1275

1279

1367

1379

1384

1386

1780

#595 LANBIC Receive Parity Error Counter Test

795

885

1623

#596 Receive FIFO Overflow Error Counter Test

886

#597 Invalid LAPD Frame Error Counter Test

887

#598 Packet Interface Test

888

#599 Packet Gateway Switched Port Loop-Around

Test

1500

#6 NPE Crosstalk Test

902

1050

#600 Congestion Query Test

889

#601Link Status Test

890

1507

#610 Packet Gateway Port Local Loop-Around

Test

1170

1171

1502

#613 Level 1 State Inquiry Test

1173

1175

1226

1229

1506

#618 BRI Port Local LAN Loop Around

806

1634

#619 BRI Port Local TDM Loop Around

808

1635

#620 Electronic Power Feed Restoral

811

#621 Level 1 Status Inquiry

812

1639

#622 Electronic Power Feed Inquiry

815

#624 Layer 1 Transmission Error Counter Test

816

#625 Receive FIFO Overflow Error Counter Test

817

1637

1638

#626 Signaling Link Status Test

831

#627 BRI Remote Loop Back

834

#628 BRI XID

837

#629 BRI Layer 3 Query

839

1642

#630 BRI Set Audits

842

#637 Remote Layer 3 Query

756

1227

1276

1382

#7 Conference Circuit Test

645

905

1052

#844-848 Transmission Test

936

1712

#884 Memory Checksum Test

1264

1473

#885 Private Loop Around Tests

1475

#886 Maintenance Loop Around Test

1477

#887 Read and Clear Board Counters

1479

#9 Digital Line NPE Crosstalk Test

1036

#976 Session Status Query Test

1227

1233

1235

1276

1383

1503

#985 System Link Status

1607

Text Checksum Test (#86)

1511

tie trunk

circuit pack option settings

124

Time Slot Test Call

TN2182 circuit packs

time division multiplex (TDM) bus clocks

1667

tone-clock

1416

TN2242

1753

TN2401

639

675

TN2501AP (integrated announcements)

faceplate LEDs, interpretation

1875

TN2793B

675

TN464 circuit pack

option settings

126

TN464 circuit packs

DS1 interface

1069

1265

1342

1374

1753

option jumpers

1763

trunks

1761

TN464C

1069

TN722 circuit packs

1069

TN760 circuit pack

option settings

124

TN767 circuit packs

1069

TN768 circuit packs

description

1416

time division multiplex (TDM) bus clocks

1667

TN780 circuit packs

time division multiplex (TDM) bus clocks

1667

TN786B

1509

TN790 Processor

TN793B

675

TN794

639

675

TN797

675

1742

TN798

1462

TN799

875

TN799 (C-LAN)

in Voice Announcements over LAN (VAL)

application

1873

TN799B

601

TN802B

601

1265

1374

1387

tone generators

1416

tone-clock circuit packs

time division multiplex (TDM) bus clocks

1667

TN2182

1416

Touch-Tone (DTMF) Receiver Test Call

traceroute

601

Trademarks

TRANS-ID

Changing the grace period interval

1740

Processor circuit pack replacement

1738

TRANS-ID (Translation-ID)

1737

transmission

errors

stream

TR-LN-BD

1742

troubleshooting

ISDN-PRI problems

ISDN-PRI test call problems

PRI endpoint problems

VAL

1877

Trunk Group Busy/Warning Indicators to Attendant

Trunk Group form

«
...
1927
1928
1929
1930
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание DEFINITY Server CSI

Отзывы:

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1929 / 1930

Результаты поиска

Содержание DEFINITY Server CSI

Отзывы: