manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1277 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1277

IPMEDPRO (IP Media Processor Circuit Pack)

Issue 5  October 2002

1277

555-233-119

2100

ABORT

The necessary system resources to execute the test could not be 
allocated.

1. Retry the command at 1-minute intervals a maximum of 5 times.

2500

ABORT

Internal system error.

1. Retry the command at 1-minute intervals a maximum of 3 times.

2801

ABORT

No IP address defined. Verify IP Interfaces translations and retest.

2802

ABORT

Different IP address pinged than software had allocated for the test.

1. Retry the command at 1-minute intervals a maximum of 3 times.

2805

FAIL

The number of pings received did not match the number sent 
(normally one ping sent). This means that no ping responses were 
received from the gateway defined on the ip-interfaces form for the 
Media Processor.

1. Retry the command at 1-minute intervals a maximum of 3 times.

2807

ABORT

The board is administered but not enabled in the change 
ip-interfaces form.

7, 89, 
1007

FAIL

A Ping to the destination failed through this port. This failure is 
because the destination is down.

1. Verify that at least one destination is reachable through this port. 

2. Once verified, execute the test port UUCSSpp command to 

verify that the H.323 Signaling Group Ping Test (#1387) passes.

PASS

Ping through this port successful.

Table 304.

TEST #1379 Ping Test  — Continued  

Error 
Code

Test 
Result

Description/ Recommendation

Continued on next page

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов