Avaya DEFINITY Server CSI Скачать руководство пользователя страница 520 | Manualshive

Страница: 520 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 520

Maintenance Commands

555-233-119

520

Issue 5 October 2002

For an ip-TDM call, the audio switch port field shows one of ports 1-8 on a
TN2302 Prowler board.

For an ip-medpro-ip hairpin call, the audio switch port field shows a cabinet and
slot, but not a port, on a TN2302 Prowler board.

status trunk 1/19 SPE B
TRUNK STATUS

Trunk Group/Member: 01/19               Service State: in-service/active
Port: T00123    Maintenance Busy? no
Signaling Group ID: 1    CA-TSC state: not allowed
  MM Conference ID: 8
   MM Endpoint ID: 2
Connected Ports: S00004

                  Switch                  IP                             IP
   Port   Near-end IP Addr: Port     Far-end IP Addr : Port
           Q.931: 12B1217 xxx.xxx.xxx.xxx : nnnnn                xxx.xxx.xxx.xxx : nnnnn
           H.245: 12B1217 xxx.xxx.xxx.xxx : nnnnn                xxx.xxx.xxx.xxx : nnnnn
G.711-MU    Audio: 12B11 xxx.xxx.xxx.xxx : nnnnn         xxx.xxx.xxx.xxx
: nnnnn

H.245 Tunneled in Q.931? no
Audio Connection Type: ip hairpin

status trunk 1/19 SPE B
TRUNK STATUS

Trunk Group/Member: 01/19               Service State: in-service/active
Port: T00123    Maintenance Busy? no
Signaling Group ID: 1    CA-TSC state: not allowed
  MM Conference ID: 8
   MM Endpoint ID: 2
Connected Ports: S00004

                  Switch                  IP                             IP
   Port   Near-end IP Addr: Port     Far-end IP Addr : Port
           Q.931: 12B1217 xxx.xxx.xxx.xxx : nnnnn                xxx.xxx.xxx.xxx : nnnnn
           H.245: 12B1217 xxx.xxx.xxx.xxx : nnnnn                xxx.xxx.xxx.xxx : nnnnn
G.711-MU     Audio: T00123  xxx.xxx.xxx.xxx : nnnnn     xxx.xxx.xxx.xxx
: nnnnn

H.245 Tunneled in Q.931? no
Audio Connection Type: ip direct

«
...
518
519
520
521
522
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов