Avaya DEFINITY Server CSI Скачать руководство пользователя страница 881 | Manualshive

Страница: 881 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 881

CLAN-BD (Control LAN Circuit Pack)

Issue 5 October 2002

881

555-233-119

q. Error Type 3586 and 3999: Switch removed hyperactive circuit pack that

reported threshold number of errors. One or more of the following
symptoms may be present:

■

Circuit pack port tests return

NO BOARD

.

■

List configuration command shows circuit pack and ports are
installed properly

1. Busyout (busyout board UUCSS) and release (release board

UUCSS) circuit pack

2. Allow 30 minutes for condition to clear itself.

3. To re-establish circuit pack into service manually, busyout (busyout

board UUCSS), reset (reset board UUCSS), and release (release
board UUCSS) the circuit pack.

4. If error recurs within 15 minutes, replace the circuit pack.

5. If the same error occurs on a different circuit pack, follow normal

escalation procedures.

r. Error Type 3840: Circuit pack received bad control channel message from

switch.

Aux Data:

s. Error Type 3841-3843: errors do not affect service.

If Error Type 3999:

And traffic
volume is:

Then:

Does not accompany
Error Type 3586

Heavy

Circuit pack is in service, but sent at least half
hyperactive threshold. With heavy traffic, this is
normal.

Does not accompany
Error Type 3586

Light

Circuit pack is in service, but sent at least half
hyperactive threshold. With light traffic, this error
indicates a problem with the circuit pack, its links, or
the equipment attached to the links.

Accompanies
Error Type 3586

Either Light or
Heavy

Switch removed hyperactive circuit pack.

4096

Bad major heading

4097

Bad port number

4098

Bad data

4099

Bad sub-qualifier

4100

State inconsistency

4101

Bad logical link

4102

Bad application identifier

«
...
879
880
881
882
883
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов