manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1345 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1345

MAPD-BD (MAPD Interface Circuit Pack TN802)

Issue 5  October 2002

1345

555-233-119

Backing up to the PCMCIA disk

Table 330

 details how to back up administration data for the IP trunk application to 

and restored from the local PCMCIA disk and the Ethernet port. Before backing 
up, be sure to shut down the application running on the circuit pack, following the 
procedures in the 

‘‘Shutting down NT on the TN802’’

 section.

NOTE:

Local restore of a complete system from the PCMCIA disk should not 
require more than 20 minutes assuming that a replacement MAPD pack is 
available and pre-loaded with the IP trunk application software. 

Restoring data from the PCMCIA disk

Before you start

1. Shut down the application running on the circuit pack. See 

‘‘Shutting down 

NT on the TN802’’

.

2. Remove the defective IP Trunk circuit pack from the switch (if applicable).

3. Install the replacement IP Trunk circuit pack in the switch (if applicable).

4. Insert the backup diskette into the IP Trunk circuit pack.

Table 330.

Backing up TN802 administration data

Step

Description

Comments

1.

Busyout circuit pack

At the Avaya Definity Server CSI terminal type 
busyout board UUCSS (the address of the 
TN802 circuit pack) and press 

Enter

.

2.

Backup administration 
TN802 to disk

At the Windows NT desktop, double-click on the IP 
Trunk Backup Restore icon.

The IP Trunk Backup/Restore Utility screen 
appears.

3.

Select utility

In the IP Trunk Backup/Restore Utility dialog 
screen, click on Files, Backup.

The IP Trunk Backup screen appears.

4.

Select backup

In the IP Trunk Backup screen, click on the 
Backup button

5.

Wait

Backup can take as much as 20 minutes to 
complete.

6.

Release circuit pack

At the Avaya Definity Server CSI terminal type 
release board UUCss (the address of the TN802 
circuit pack) and press 

Enter

.

Continued on next page

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов