Avaya DEFINITY Server CSI Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 91

Troubleshooting Features

Issue 5 October 2002

91

555-233-119

The troubleshooting procedure described here diagnoses faults between the
switch and the line-side PRI terminal adapter/ISDN-PRI endpoint equipment.
Problems encountered on the network-side of a wideband connection or problems
with end-to-end equipment compatibility are outside the scope of this manual.

Figure 7.

Processing of PRI Endpoint Problems (Page 1 of 2)

Does

the

PRI Terminal

Adapter or the

ISDN endpoint

equipment

indicate alarms or

errors? Check the

endpoint equipment

for status - not

the

SAT

START

END

YES

A

YES

YES

FOLLOW REPAIR PROCEDURE

IN THE PE-BCHL MO SECTION

FOLLOW REPAIR PROCEDURE

RECOMMENDED BY THE PRI

TERMINAL ADAPTER

VENDOR

OR ISDN ENDPOINT

EQUIPMENT VENDOR

Are there
alarms or

errors against

DS1-BD?

YES

IF MULTIPLE ALARMS EXIST,

INVESTIGATE IN THE

FOLLOWING ORDER: PI-BD,

PI-PT, PI-SCI, PI-LINK,

ISDN-LNK, AND ISDN-SGR.

FOLLOW REPAIR PROCEDURE

FOR APPROPRIATE MO.

YES

NO

FOLLOW REPAIR PROCEDURE

IN THE DS1-BD MO SECTION

NO

Are there

alarms or

errors against

PI-BD, PI-PT,

PI-SCI, PI-LINK,

ISDN-SGR, or

ISDN-

LNK?

TO

PAGE 2

FIX ADMINISTRATION

MISMATCH

NO

NO

NO

Are there
alarms or

errors against

PE-BCHL?

Is the

administration

between the endpoint

equipment and the

switch consistent?

(for example, port

boundary,

width, etc.)

«
...
89
90
91
92
93
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов