Error Code List Chapter4. Cash & Check In Module
4-136
© 2014
Nautilus Hyosung Inc.
All Rights Reserved.
Code
Problem Description
Troubleshooting
I5512
[Deposit Reject]Jam between the
Escrow entry (ESS04) and
(FDS15) when processing drum
full while storing the media.
1. Open the Escrow Part(12).
2. Remove the media at the Escrow
entry (FDS15) and output check
(ESS04) sensor part and the pollution.
3. Execute CCIM initialization.
I5513
[Deposit Reject]Escrow Tape End
(ESS07) detection fault when
executing media winding.
1. Open the Escrow part (12) and
remove the ESS07 media and pollution.
2. Rotate the Escrow Knob in
counterclock-wise three times.
3. Execute CCIM initialization.
I5514
[Deposit Reject]Escrow Full
(ESS05) detection fault when
storing additional media while
terminating media winding.
1. Open the Escrow part (12) and
remove the ESS05 media and pollution.
2. Rotate the Escrow Knob in
counterclock-wise three times.
3. Execute CCIM initialization.
I5515
[Deposit Reject]Fault of
performing a undefined process
flow from Escrow.
1. Execute CCIM initialization.
2. Reboot the system when the same
error occurs after initialization.
I5516
[Deposit Reject] Residual
detection (ESS03) Jam before
Escrow Drum when outputting the
media.
1. Open the Escrow Part(12).
2. Remove the ESS03 media and
pollution.
3. Execute CCIM initialization.
I5517
[Deposit Reject]Light jam at the
Escrow output check sensor
(ESS04) when outputting the
media.
1. Open the Escrow Part(12).
2. Remove the ESS04 media and
pollution.
3. Execute CCIM initialization. 4. Check
the Escrow Drum running motor
(ESM01).
I5518
[Deposit Reject]Residual media in
the Escrow (ESS01, ESS02) when
preparing for media discharge.
1. Open the Escrow Part(12).
2. Remove the ESS01 and ESS02
media and pollution.
3. Execute CCIM initialization.
I5519
[Deposit Reject] Escrow Trigger2
(ESS04) is not detected and
timeout occurs when outputting
the media.
1. Open the Escrow Part(12).
2. Remove the ESS04 media and
pollution.
3. Execute CCIM initialization. 4. Check
the Escrow Drum running motor
(ESM01).
I551A
[Deposit Reject] Residual
detection sensor (ESS03) Jam
before Escrow Drum when
outputting the media.
1. Open the Escrow Part(12).
2. Remove the ESS03 media and
pollution.
3. Execute CCIM initialization.
I551B
[Deposit Reject]Jam at the Escrow
output check sensor (ESS04)
when outputting the media.
1. Open the Escrow Part(12).
2. Remove the ESS04 media and
pollution.
3. Execute CCIM initialization.
I551C
[Deposit Reject]Residual media in
the Escrow (ESS01, ESS02) when
preparing for media discharge.
1. Open the Escrow Part(12).
2. Remove the ESS01 and ESS02
media and pollution.
3. Execute CCIM initialization.
I5520
[Deposit Reject]For Escrow Drum
winding (50ms+2591Step), the
tape start is not light-detected for
50ms continuously, and a fault
occurs when 6s is exceeded.
1. Open the Escrow Part(12).
2. Remove the ESS06 media and
pollution.
3. Check Motor (ESM01)
4. Execute CCIM initialization.