manualshive.com logo in svg

Texas Instruments OMAP36 Series, Техническое справочное руководство


Поделиться
Скачать
background image

Public Version

Display Subsystem Register Manual

www.ti.com

Bits

Field Name

Description

Type

Reset

15

VC_BUSY

Indicates if previously scheduled activities (packets, BTA)

R

0x0

are still being processed. Forced to 1 by hardware if VC
is enabled. Software should check this bit is 0 before
changing channel configuration.

0x0: No pending operations for this VC

0x1: Pending operations for this VC

14

PP_BUSY

Line buffer busy status.

R

0

0x0: Software is permitted to write a new header for VP
command mode traffic.

0x1: Software is NOT permitted to write a new header for
VP command mode traffic.

13:10

RESERVED

Write 0s for future compatibility.

RW

0x00

Reads returns 0.

9

MODE_SPEED

Selection of the mode. This bit is ignored by hardware

RW

0x0

when video mode is selected.

0x0: Low-power mode (CMOS) is used to send short and
long packets to the peripheral.

0x1: High speed mode (SLVS) is used to send short and
long packets to the peripheral.

8

ECC_TX_EN

Enables the ECC generation for the transmit header

RW

0x0

(short and long packets).

0x0: Disabled

0x1: Enabled

7

CS_TX_EN

Enables the checksum generation for the transmit

RW

0x0

payload (long packet only).

0x0: Disabled. The value 0x00 is used.

0x1: Enabled. The Check-sum value is calculated by HW.

6

BTA_EN

Send the bus turn around to the peripheral. It can be

RW

0x0

used when the automatic mode is enabled
(BTA_SHORT_EN=1 or/and BTA_LONG_EN=1). In that
case only one BTA is sent to the peripheral. The manual
mode allows users to define for which packets, the turn
around is required for example getting acknowledge from
the peripheral.

0x0: READS: BTA generation is completed. It is reset by
HW when it is completed.
WRITES: Cancellation of the BTA generation (not
guarantee since it could already on going, must not be
used).

0x1: READS: BTA generation has been requested by
user (it could be on going but not completed).
WRITES: Request for BTA generation.

5

TX_FIFO_NOT_EMPTY

FIFO status

R

0x0

0x0: The TX FIFO is empty (the FIFO does not contain
any data for the VC)

0x1: The TX FIFO is not empty (the FIFO contains at
least one byte for the VC)

4

MODE

Selection of the mode

RW

0x0

0x0: Command mode.

0x1: Video mode.

3

BTA_LONG_EN

Enables the automatic bus turn-around after completion

RW

0x0

of each long packet transmission.

0x0: Disabled

0x1: Enabled

2

BTA_SHORT_EN

Enables the automatic bus turn-around after completion

RW

0x0

of each short packet transmission.

0x0: Disabled

0x1: Enabled

1944

Display Subsystem

SWPU177N – December 2009 – Revised November 2010

Copyright © 2009–2010, Texas Instruments Incorporated

Содержание OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP36 Series

Jetter JXM-IO-E30 Installation Manual preview
JXM-IO-E30
Бренд: Jetter Страницы: 35
IOtech ADAC/5500MF Installation Manual preview
ADAC/5500MF
Бренд: IOtech Страницы: 16
Dazzle Hollywood DV-Bridge User Manual preview
Hollywood DV-Bridge
Бренд: Dazzle Страницы: 63
Internet Security Systems Proventia A1204 User Manual preview
Proventia A1204
Бренд: Internet Security Systems Страницы: 42
National Instruments PCI-6110E/6111E User Manual preview
PCI-6110E/6111E
Бренд: National Instruments Страницы: 113
EK EK-Quantum Momentum ROG Rampage VI Encore User Manual preview
EK-Quantum Momentum ROG Rampage VI Encore
Бренд: EK Страницы: 11
Bitspower BPTA-CPUMS-V2-SKA Instruction Manual preview
BPTA-CPUMS-V2-SKA
Бренд: Bitspower Страницы: 6
Ubiquiti UniFi WiFi BaseStation XG Quick Start Manual preview
UniFi WiFi BaseStation XG
Бренд: Ubiquiti Страницы: 19
CG Emotron OSTO 100 Instruction Manual preview
Emotron OSTO 100
Бренд: CG Страницы: 112
V-Count Ultima Go Quick Installation Manual preview
Ultima Go
Бренд: V-Count Страницы: 2
Digi DataFire GO! PRO Manual preview
DataFire GO! PRO
Бренд: Digi Страницы: 20
Kontron AdvancedTCA AT8901M User Manual preview
AdvancedTCA AT8901M
Бренд: Kontron Страницы: 76
VIA Technologies Mobile360 M810 Quick Start Manual preview
Mobile360 M810
Бренд: VIA Technologies Страницы: 25
Watchguard Firebox T20 Hardware Manual preview
Firebox T20
Бренд: Watchguard Страницы: 21
ZyXEL Communications POE-12 Specifications preview
POE-12
Бренд: ZyXEL Communications Страницы: 2
COUGAR Vortex SPB 120 User Manual preview
Vortex SPB 120
Бренд: COUGAR Страницы: 2
Serial Cables PCI-AD-x16HE-BG4 User Manual preview
PCI-AD-x16HE-BG4
Бренд: Serial Cables Страницы: 18
HighPoint SSD7202 Quick Installation Manual preview
SSD7202
Бренд: HighPoint Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды