manualshive.com logo in svg

Texas Instruments OMAP36 Series, Техническое справочное руководство


Поделиться
Скачать
background image

Public Version

Camera ISP Functional Description

www.ti.com

6.4.6.1.4 Camera ISP CCDC DMA

The CCDC module is a master. It has its own address generator and sends addresses and data to the
central-resource shared-buffer logic. The central-resource shared-buffer logic arbitrates the data requests
and generates the bursts to memory.

6.4.6.1.5 Camera ISP CCDC Memories

The CCDC module has one memory:
•

REFORMATTER BUFFER: 3 x 1376 x 40 bits

•

LSC PREFETCH BUFFER: 1536 x 32 bits

6.4.7 Camera ISP Video-Processing Back End

The video-processing back end (VPBE) comprises the preview and Resizer modules.

6.4.7.1

Camera ISP VPBE Preview Engine Features

The preview module is responsible for transforming data from a RAW image sensor into YUV422 data that
is amenable to still-image encoding, video encoding, or display. It supports the following features:

•

Flexible input: Module input data can come from the RAW image sensor (10 bits) or from memory (8 or
10 bits).

•

Flexible input formats: Bayer RGB color filter array, complementary-color filter array, Super CCD
Honeycom® sensors

•

Horizontal averaging by a factor of 1, 2, 4, or 8 in the horizontal direction. The preview module can
output a maximum of only 4096 pixels horizontally due to fixed memory-line sizes.

•

A-Law decompression: Transforms nonlinear 8-bit data to 10-bit linear data. The CCDC module can
perform A-Law compression.

•

Noise reduction and faulty-pixel correction:

–

Dark-frame capture and subtraction

–

Horizontal median filter

–

Programmable noise filter: 3x3 kernel of same color pixels

–

Couplet faulty-pixel correction

•

Digital gain and white balance

•

Programmable CFA interpolation that operates on a 5x5 grid

•

Programmable RGB-to-RGB blending matrix: 9 coefficients for the 3x3 matrix

•

Programmable gamma correction: 1024 entries for each color held in local memory

•

Programmable RGB-to-YUV color conversion: 9 coefficients for the 3x3 matrix

•

Luminance enhancement (nonlinear), chrominance suppression and offset

6.4.7.1.1 Camera ISP VPBE Preview Block Diagram

Figure 6-84

shows the preview engine block diagram.

1206

Camera Image Signal Processor

SWPU177N – December 2009 – Revised November 2010

Copyright © 2009–2010, Texas Instruments Incorporated

Содержание OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP36 Series

Samsung AllShare Cast Dongle Quick Start Manual preview
AllShare Cast Dongle
Бренд: Samsung Страницы: 2
D-Link DSL-2750U Setup preview
DSL-2750U
Бренд: D-Link Страницы: 14
Quantum Scalar 50 Upgrade Instructions preview
Scalar 50
Бренд: Quantum Страницы: 20
Direct IP IDIS DR-1304P Operation Manual preview
IDIS DR-1304P
Бренд: Direct IP Страницы: 76
Comelit IPNVR004BPOE Manual preview
IPNVR004BPOE
Бренд: Comelit Страницы: 19
Echo LAYLA 3G Owner'S Manual preview
LAYLA 3G
Бренд: Echo Страницы: 21
Paradyne 8310 MVLt User Manual preview
8310 MVLt
Бренд: Paradyne Страницы: 108
ADTRAN 1200127L1 User Manual preview
1200127L1
Бренд: ADTRAN Страницы: 20
ASTRO U 960 Operating Manual preview
U 960
Бренд: ASTRO Страницы: 12
Extron electronics StudioStation 100 User Manual preview
StudioStation 100
Бренд: Extron electronics Страницы: 131
ProCurve 800 Configuration Manual preview
800
Бренд: ProCurve Страницы: 406
Motorola solutions Avigilon HD-NVR4-PRM-128TB User Manual preview
Avigilon HD-NVR4-PRM-128TB
Бренд: Motorola solutions Страницы: 31
Hitachi KNX001 Installation And Operation Manual preview
KNX001
Бренд: Hitachi Страницы: 14
Hitachi SJ/L-EN Ethernet Communications Module Instruction Manual preview
SJ/L-EN Ethernet Communications Module
Бренд: Hitachi Страницы: 36
Hitachi 3080 G2 Hardware Reference Manual preview
3080 G2
Бренд: Hitachi Страницы: 129
Hitachi 9900 Series User And Reference Manual preview
9900 Series
Бренд: Hitachi Страницы: 138
D-Link xStack DGS-3426P Reference Manual preview
xStack DGS-3426P
Бренд: D-Link Страницы: 629
Domburg KeerPlus3 Manual preview
KeerPlus3
Бренд: Domburg Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды