Texas Instruments OMAP36 Series Technical Reference Manual Download Page 3322 | Manualshive

Page: 3322 / 3738

background image

Public Version

High-Speed USB Host Subsystem

www.ti.com

Table 22-152. ULPI_VENDOR_INT_LATCH_i

Address Offset

0x0000 003F + (0x100 * i)

Index

i = 0 to 2

Physical Address

0x4806 283F + (0x100 * i)

Instance

USBTLL

Description

Vendor-specific interrupt latches for miscellaneous ULPI alt_int events. Cleared upon read, and when
Low Power Mode, Serial Mode or Carkit Mode are entered.

Type

R

7

6

5

4

3

2

1

0

RESERVED

P2P_LATCH

Bits

Field Name

Description

Type

Reset

7:1

RESERVED

Reserved

R

0x00

0

P2P_LATCH

PHY-to-PHY ULPI wakeup event latch. Set when ULPI is

R

0x0

in low-power mode (suspendm = 0) and UTMI is active
(suspendm = 1).

0x0: No PHY-to-PHY wakeup event latched

0x1: PHY-to-PHY wakeup event was latched, ALT
interrupt active

Table 22-153. Register Call Summary for Register ULPI_VENDOR_INT_LATCH_i

High-Speed USB Host Subsystem

•

High-Speed USB Host Subsystem Register Summary

22.2.6.4.2 UHH_config Registers

Table 22-154. UHH_REVISION

Address Offset

0x0000 0000

Physical Address

0x4806 4000

Instance

UHH_config

Description

Standard revision number, BCD encoded Revision = <maj>.<min>

Type

R

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

MAJ_REV

MIN_REV

Bits

Field Name

Description

Type

Reset

31:8

RESERVED

Reserved

R

0x000000

7:4

MAJ_REV

Major revision number 0..9

R

0x1

3:0

MIN_REV

Minor revision number 0..9

R

0x0

Table 22-155. Register Call Summary for Register UHH_REVISION

High-Speed USB Host Subsystem

•

High-Speed USB Host Subsystem Register Summary

3322

High-Speed USB Host Subsystem and High-Speed USB OTG Controller

SWPU177N – December 2009 – Revised November 2010

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
3320
3321
3322
3323
3324
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

ShareCenter Pulse DNS-320

Brand: D-Link Pages: 2

Brand: D-Link Pages: 4

Brand: ICP DAS USA Pages: 48

Brand: ICP DAS USA Pages: 24

Brand: Quantum Pages: 20

Brand: Hama Pages: 12

Brand: TP-Link Pages: 2

Parallel & Serial Port Checker PPC

Brand: B&B Electronics Pages: 4

Brand: IEI Technology Pages: 86

Lite N42B1P Series

Brand: Dahua Technology Pages: 14

Millennium P650

Brand: Matrox Pages: 54

Brand: Paradyne Pages: 10

DIRECTOR PRO series

Brand: MF DIGITAL Pages: 79

Brand: Renesas Pages: 20

Optane Persistent Memory 200 Series

Brand: Supermicro Pages: 54

Airborne M2M ABDN-er-DP55 Series

Brand: B+B SmartWorx Pages: 120

Brand: DigiTech Pages: 28

CloudGen Firewall

Brand: Barracuda Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands