Texas Instruments OMAP36 Series Technical Reference Manual Download | Manualshive

Page: 3574 / 3738

background image

Public Version

Device Initialization by ROM Code

www.ti.com

Table 26-44. CHFLASH (continued)

Offset

Field

Description

0008h

GPMC_SYSCONFIG (LSB)

Register value

000Ah

GPMC_IRQENABLE (LSB)

000Ch

GPMC_TIMEOUT_CONTROL (LSB)

000Eh

GPMC_CONFIG (LSB)

0010h

GPMC_CONFIG1_0

0014h

GPMC_CONFIG2_0

0018h

GPMC_CONFIG3_0

001Ch

GPMC_CONFIG4_0

0020h

GPMC_CONFIG5_0

0024h

GPMC_CONFIG6_0

0028h

GPMC_CONFIG7_0

002Ch

GPMC_PREFETCH_CONFIG1

0030h

GPMC_PREFETCH_CONFIG2 (LSB)

0032h

GPMC_PREFETCH_CONTROL (LSB)

0034h

GPMC_ECC_CONFIG

0036h

GPMC_ECC_CONTROL

0038h

GPMC_ECC_SIZE_CONFIG (LSB)

0: Do not change A1– A10

003Ch

Enable_A1_A10

Others: Enable pins A1 – A10

26.4.8.2.4 CHMMCSD

The CHMMCSD configuration header contains settings specific to the high-speed MMC/SD/SDIO host
controller (MMCHS). For more information, see

, MMC/SD/SDIO Card Interface.

lists the fields. The ROM code configures the MMCHS by default to these settings:

•

400-kHz clock during identification mode

•

19.2-MHz clock during data transfer mode

Table 26-45. CHMMCSD CH

Offset

Register Modified

Description

Key used for section verification

0000h

Section key

C0C0C0C4h

Enables/disables the section

0004h

Valid

00h: Disable

Other: Enable

0005h

Reserved

0008h

MMCHS_SYSCTRL(MSB)

Register value

000Ah

MMCHS_SYSCTRL(LSB)

0xFFFFFFFF -> Do not update register.

1 -> 1 bit

2 -> 4 bits

000Ch

Bus width

4 -> 8 bits (on SD/MMC2 interface only)

0xFFFFFFFF -> Do not update register.

NOTE:

The ROM code transmits a booting parameter structure to the initial software (see

Section 26.4.8.4

, Image Execution). This structure contains a field that indicates whether the

configuration header sections have been correctly considered. For the CHMMCSD section, if
all the section fields are set to 0xFFFFFFFF, regardless of the value of the VALID bit field,
the booting parameters should indicate that the CHMMCSD section has not been executed.

3574

Initialization

SWPU177N – December 2009 – Revised November 2010

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
3572
3573
3574
3575
3576
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 5

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 21

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 2

WJMPU955 - PROCESSING UNIT - TMU

Brand: Panasonic Pages: 62

Brand: 3Com Pages: 8

Brand: Udoo Pages: 7

Brand: ICP DAS USA Pages: 48

Brand: ICP DAS USA Pages: 24

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 5

Brand: SeaLevel Pages: 17

Magic WiFi mini Ek

Brand: Devolo Pages: 22

Brand: ZALMAN Pages: 9

Brand: Omron Pages: 13

Brand: XtendLan Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands