manualshive.com logo in svg

NXP Semiconductors MWCT101 S Series, Reference Manual

Share
Download
NXP Semiconductors MWCT101 S Series Reference Manual Download Page 1721

Table 50-9. MDM-AP Status Register assignments (continued)

Bit

Name

Description

5

Mass erase enable

Indicates whether the MCU can be mass erased

0: Mass erase is disabled

1: Mass erase is enabled

6

Backdoor access key enable

Indicates whether the MCU has the backdoor access key enabled. See the
FTFE_FSEC[KEYEN] bit for more information.

0: Disabled

1: Enabled

7

LP enabled

Decode of LPLLSM control bits to indicate that VLPS is the selected power
mode the next time the Arm core enters Deep Sleep.

0: Low Power Stop Mode is not enabled

1: Low Power Stop Mode is enabled

Usage is intended for debug operation in which Run to VLPS is attempted.
Per debug definition, the system actually enters the Stop state. A
debugger should interpret deep sleep indication (with SLEEPDEEP and
SLEEPING asserted) in conjunction with this bit asserted as the debugger-
VLPS status indication.

8

Very low power mode

Indicates current power mode is VLPx. This bit is not ‘sticky’ and should
always represent whether VLPx is enabled or not.

This bit is used by the debugger to throttle JTAG TCK frequency up/down.

9 – 10

Reserved

Always reads as 0.

11 – 15

Reserved for future use

Always read as 0.

16

Core halted

Indicates the core has entered debug halt mode

17

Core SLEEPDEEP

Indicates the core has entered a low power mode

SLEEPING==1 and SLEEPDEEP==1 indicates stop or VLPS mode.

18

Core SLEEPING

19 – 31

Reserved for future use

Always reads as 0.

50.7 Debug resets

The debug system receives the following sources of reset:

• Debug reset (CDBGRSTREQ bit within the SWJ-DP CTRL/STAT register) in the

TCLK domain that allows the debugger to reset the debug logic

• System POR reset

Conversely, the debug system is capable of generating system reset using the following
mechanism:

• A system reset in the DAP control register which allows the debugger to hold the

system in reset

• SYSRESETREQ bit in the NVIC application interrupt and reset control register

Chapter 50 Debug

MWCT101xS Series Reference Manual, Rev. 3, 07/2019

NXP Semiconductors

1721

Summary of Contents for MWCT101 S Series


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands