NXP Semiconductors MWCT101 S Series Reference Manual Download Page 1320 | Manualshive

Page: 1320 / 1761

background image

42.5.3 Timer Modes

The timer mode is configured by setting an appropriate value in the MODE bits in
TCTRLn register.

Table 42-4. Timer modes that are supported

Timer Mode

Operation

32-bit Periodic Counter

• The counter will load, decrement down to 0
• which will set the timer interrupt flag and assert the output pre-trigger.

Dual 16-bit Periodic
Counter

• The counter will load, then the lower 16-bits will decrement down to 0
• which will assert the output pre-trigger.
• The upper 16-bits will then decrement down to 0
• which will set the timer interrupt flag and then negate the output pre-trigger.

32-bit Trigger
Accumulator

• The counter will load on the 1st trigger rising edge and then decrement down to 0 on each

trigger rising edge

• which will set the timer interrupt flag and assert the output pre-trigger.

32-bit Trigger Input
Capture

• The counter will load with 0xFFFF_FFFF and then decrement down to 0.
• If a trigger rising edge is detected,

• then it will store the inverse of the current counter value in the timer value register
• which will set the timer interrupt flag and assert the output pre-trigger.

The timer operation is controlled by Trigger Control bits (TSOT, TSOI, TROT) which
control the timer load, reload, start and restart of the timers.

NOTE

• The trigger output is asserted one Peripheral Timer Clock

cycle later than pre-trigger output. The trigger output and
the pre-trigger output de-assert at the same time.

• The pre-trigger output is asserted for 2 clock cycles and the

trigger output is asserted for 1 clock cycle (except in 16-bit
Periodic Counter mode, where both pre-trigger and trigger
are asserted for many cycles depending on
TMR_VAL[31:16]).

• Timer changes that are based on external triggers take

effect after 4 peripheral clocks after the actual external
trigger assertion (due to clock synchronization, rise edge
detection and timer update).

42.5.4 Trigger Control for Timers

Various programmable bits control how the trigger inputs and the timer operate.
TRG_SEL and TRG_SRC select the timer triggers:

Functional description

MWCT101xS Series Reference Manual, Rev. 3, 07/2019

1320

NXP Semiconductors

«
...
1318
1319
1320
1321
1322
...
»

Summary of Contents for MWCT101 S Series


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MWCT101 S Series

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands