BUS Updated 12/2011
07/2011
2-88
WorkCentre 5335 Family Service Documentation
012-151 (Integrated Finisher)
Initial Issue
Status Indicator RAPs
012-151 (Integrated Finisher) Compiler Exit Sensor OFF
Jam RAP
BSD-ON:
BSD 12.3 Integrated Finisher Transportation
The Compiler Exit Sensor does not turn Off within a specified time after it has turned On.
Initial Actions
•
Check the Compiler Exit Sensor is properly installed and free from foreign objects and
that the actuator is not binding.
•
Power Off/On.
Procedure
Check the specifications of paper. Paper is in spec.
Y
N
Replace the paper with new paper that is in spec.
Check the condition of the paper. The paper is in normal condition without any problem
that causes the paper to be bent or caught.
Y
N
Resolve any problem that causes the paper to be bent or caught.
Check the transport path for a foreign object, deformed part, and paper dust. The transport
path is in normal condition with no foreign object, deformed part and paper dust.
Y
N
Repair the deformed part(s) and remove the foreign object(s) and paper dust.
Check the Transport Roll for wear, deterioration and paper dust. The Transport Roll is in
normal condition, not worn and deteriorated and with no paper dust.
Y
N
Remove the paper dust and replace the worn or deteriorated Transport Roll.
Check the drive mechanism to the Transport Roll for a deformed, broken part, and/or belt dam-
age. The drive mechanism is free of defects.
Y
N
Repair defects or damage to the drive mechanism.
Enter
Component Control
[012-150]. Actuate the Compiler Exit Sensor. The display
changes.
Y
N
Check the connections of
P/J8709
and
P/J8728
.
P/J8709
and
P/J8728
are securely
connected.
Y
N
Connect
P/J8709
and
P/J8728
securely.
Check for an open or short circuit between
P/J8709
and
P/J8728
. The wire
P/J8709
and
P/J8728
are OK.
Y
N
Repair the open or short circuit.
Measure the voltage between Finisher PWB
P/J8709
-3 (+) and GND (-). The voltage is
approx. +5VDC.
Y
N
Go to
Integrated Finisher Wirenets
and check the +5VDC circuit.
Measure the voltage between Finisher PWB
P/J8709
-2 (+) and GND (-). Actuate the
Compiler Exit Sensor. The voltage changes.
Y
N
Replace the Compiler Exit Sensor (
PL 22.5
).
Check the wires and connectors for an intermittent open or short circuit. If the problem
continues, replace the Finisher PWB (
PL 22.7
).
Enter [012-095]. The Finisher Transport Motor rotates.
Y
N
Check the connections of
P/J8706
and
P/J8739
.
P/J8706
and
P/J8739
are securely
connected.
Y
N
Connect
P/J8706
and
P/J8739
securely.
Check for an open or short circuit between
P/J8706
and
P/J8739
. The wire between
P/J8706
and
P/J8739
are OK.
Y
N
Repair the open or short circuit.
Measure the voltage between Finisher PWB
P/J8706
-5 (+) and GND (-), and
P/J8706
-7
(+) and GND (-). Each voltage is approx. +24VDC.
Y
N
Go to
Integrated Finisher Wirenets
and check the +24VDC circuit.
Check the wires and connectors for an intermittent open or short circuit. If the problem
continues, replace the Finisher Transport Motor (
PL 22.4
). If the problem persists, replace
the Finisher PWB (
PL 22.7
).
Enter [012-013]. When the Sub Paddle Solenoid is turned On/Off, the Sub Paddle Shaft
Assembly goes down/up.
Y
N
Check the Sub Paddle mechanism for a deformed or broken part and not-seated gears.
The Sub Paddle mechanism is free from defects and gears are seating properly.
Y
N
Repair defects to the Sub Paddle mechanism.
Check the connections of
P/J8705
and
P/J8734
.
P/J8705
and
P/J8734
are securely
connected.
Y
N
Connect
P/J8705
and
P/J8734
securely.
Check for an open or short circuit between
P/J8705
and
P/J8734
. The wires between
P/J8705
and
P/J8734
are OK.
Y
N
Repair the open or short circuit.
A
A
B
B
C
D