![background image](http://html.mh-extra.com/html/xerox/workcentre-5335-series/workcentre-5335-series_service-manual_8843081265.webp)
BUS Updated 12/2011
07/2011
4-210
WorkCentre 5335 Family Service Documentation
ADJ 9.10
Initial Issue
Repairs & Adjustments
ADJ 9.10 IOT Lead Edge/Side Edge Registration
Purpose
The purpose is to adjust the position of the printed image on the page by controlling where the
ROS writes the image. This is done by changing the value of the Lead Edge Registration and
Side Edge Registration in UI Diagnostics. This adjustment must be completed prior to the IIT
Lead Edge/Side Edge Registration, and the DADF Lead Edge Registration.
Each tray must be adjusted separately for:
•
Lead Edge registration for side 1
•
Lead Edge registration for side 2
•
Side Edge registration for side 1
•
Side Edge registration for side 2
Specification
The specifications for Lead Edge and Side Edge are shown in the table below.
Checking Side 1 Lead Edge Registration
1.
Load Trays 1 and 2, and the Tray 5 / Bypass, with 11 x 17 / A3 Bond/Plain paper. Load
Trays 3, 4, and 6 with 8 1/2 x 11 / A4 Bond/Plain paper.
2.
The routine automatically selects the appropriate NVM location to set, based on the
Paper Type setting for the trays.
3.
Enter UI diagnostics (
Entering and Exiting Service Rep. Mode
).
4.
Press the Machine Status button on the control panel.
5.
Select the Tools tab on the UI screen.
6.
System Settings and Common Service Settings will be highlighted.
7.
In the Features column, scroll to and select Maintenance / Diagnostics.
8.
Scroll to and select Registration, then select System Registration Adjustment.
9.
Make the following selections:
a.
Select Side 1, if not already selected.
b.
Select Tray 1, if not already selected.
c.
Select 5 for Print Count.
10. Select Print on the UI.
11.
Remove the prints one at a time from the center output tray and Flip each one Right to
Left, to position it as shown in
Figure 1
(lead edge to the left).
12. Label each printed sheet with the number of the print (1 through 5), the words “Tray 1,”
and “Side 1,” and the location of the Lead Edge of each sheet.
13. Take the third print and measure from the lead edge to point A (as shown on
Figure 1
).
Point A is at the intersection of the 7th line from the side edge and the first line from the
lead edge.
14. If the measured value is not 10 +/- 1.5mm, perform the
Adjustment
. If the Check is OK,
repeat steps 5 through 8 for Trays 2 - 5.
15. After all trays are set, proceed to
Checking Side 2 Lead Edge Registration
.
Figure 1 Test Pattern Measurement Points
Checking Side 2 Lead Edge Registration
NOTE: The grid pattern for side 1 does not align with the side 2 grid pattern; do not attempt to
set registration by aligning the grids.
1.
Make the following selections:
a.
Select Tray 1, if not already selected.
b.
Select Side 2.
c.
Select 5 for Print Count, if not already selected.
2.
Click Print.
NOTE: “Side 2” will be delivered face-down in the tray, with the Lead edge to the right. Flip
each one Right to Left to position it as shown in
Figure 1
(lead edge to the left).
3.
Label each printed sheet with the number of the print (1 through 5), the words “Tray 1”
and “Side 2,” and the location of the Lead Edge of each sheet.
4.
Take the third print and measure from the lead edge to point A (as shown on
Figure 1
).
Point A is at the intersection of the 7th line from the side edge and the first line from the
lead edge.
5.
If the measured value is not 10 +/- 1.5mm, perform the
Adjustment
. If the Check is OK,
repeat steps 2 through 4 for Trays 2 - 5.
6.
After all trays are set, proceed to
Checking Side 1 Side Edge Registration
.
Table 1 Specification
Item
Simplex
Duplex
Tray 5 / Bypass
Lead Edge
10 +/- 1.5mm
10+/- 1.5mm
10+/- 1.5mm
Side Edge
8.5+/- 1.7mm
8.5 +/-1.7mm
8.5+/- 2.9mm