manualshive.com logo in svg

NXP Semiconductors PXN2020, Reference Manual, Page: 409 / 1376

Share
Download
NXP Semiconductors PXN2020 Reference Manual Download Page 409

e200z0 Core (Z0)

PXN20 Microcontroller Reference Manual, Rev. 1

Freescale Semiconductor

14-11

14.3.3

e200z0 Core Complex Features not Supported on the PXN20 

The PXN20 implements a subset of the e200z0 core complex features. The e200z0 core complex features 
that are not supported in the PXN20 are described in 

Table 14-2

.

14.4

Interrupt Types

The interrupts implemented on the PXN20 and the exception conditions that cause them are listed in 

Table 14-3

.

Table 14-2. e200z0 Features Not Supported on the PXN20

Description

Function/Category

The less significant halfword of the Processor Version Register (PVR) provides the revision 
level which is comprised of the following three bit fields:
Reserved = 0x00
Revision = 0x0
ID = 0x0
The more significant halfword of the Processor Version Register (PVR) provides the 
processor type and version number (see 

Table 14-1

).

PVR Value

Nexus registers are not accessible by code running in User or Supervisor mode. Nexus 
registers can be accessed only by external tools via the Nexus port.

Debug

Table 14-3. Exceptions and Conditions

Interrupt Type

 Interrupt Vector 

Offset Register

Causing Conditions

System reset

none, vector to 
address determined 
by CRP_Z0VEC

1. Reset.

2. Debug Reset Control.

Critical Input

IVOR 0

1

Non-maskable interrupt request and MSR[CE] = 1.

Machine check

IVOR 1

1. Machine check error and MSR[ME] = 1.

2. Bus error (XTE) with MSR[EE] = 0 and current MSR[ME] = 1

Data Storage

IVOR 2

1. Access control. (unused on e200z0)

2. Precise external termination error and MSR[EE] = 1.

Instruction 
Storage

IVOR 3

1. Access control. (unused on e200z0)

2. Precise external termination error and MSR[EE] = 1.

External Input

IVOR 4

1

 Interrupt request and MSR[EE] = 1.

Alignment

IVOR 5

1. lmw, stmw not word aligned.

2. lwarx or stwcx. not word aligned.

Program

IVOR 6

Illegal, Privileged, Trap, Unimplemented Operation.

Floating-point 
unavailable

IVOR 7

Unused

System call

IVOR 8

Execution of the System Call (se_sc) instruction

Summary of Contents for PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments