manualshive.com logo in svg

NXP Semiconductors PXN2020, Reference Manual, Page: 641 / 1376

Share
Download
NXP Semiconductors PXN2020 Reference Manual Download Page 641

FlexRay Communication Controller (FlexRAY)

PXN20 Microcontroller Reference Manual, Rev. 1

Freescale Semiconductor

26-27

26.5.2.14 Protocol Interrupt Enable Register 1 (PIER1)

This register defines whether or not the individual interrupt flags defined in 

Protocol Interrupt Flag 

Register 1 (PIFR1)

 can generate a protocol interrupt request.

LTXA_IE

pLatestTx

 Violation on Channel A Interrupt Enable — This bit controls LTXA_IF interrupt request generation.

0 interrupt request generation disabled.

1 interrupt request generation enabled.

TBVB_IE

Transmission across boundary on channel B Interrupt Enable — This bit controls TBVB_IF interrupt request 
generation.

0 interrupt request generation disabled.

1 interrupt request generation enabled.

TBVA_IE

Transmission across boundary on channel A Interrupt Enable — This bit controls TBVA_IF interrupt request 
generation.

0 interrupt request generation disabled.

1 interrupt request generation enabled.

TI2_IE

Timer 2 Expired Interrupt Enable — This bit controls TI1_IF interrupt request generation.

0 interrupt request generation disabled.

1 interrupt request generation enabled.

TI1_IE

Timer 1 Expired Interrupt Enable — This bit controls TI1_IF interrupt request generation.

0 interrupt request generation disabled.

1 interrupt request generation enabled.

CYS_IE

Cycle Start Interrupt Enable — This bit controls CYC_IF interrupt request generation.

0 interrupt request generation disabled.

1 interrupt request generation enabled.

Base + 0x001E

Write: Anytime

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R EMC

_IE

IPC

_IE

PECF

_IE

PSC

_IE

SSI3

_IE

SSI2

_IE

SSI1

_IE

SSI0

_IE

0

0

EVT

_IE

ODT

_IE

0

0

0

0

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 26-14. Protocol Interrupt Enable Register 1 (PIER1)

Table 26-20. PIER1 Field Descriptions

Field

Description

EMC_IE

Error Mode Changed Interrupt Enable — This bit controls EMC_IF interrupt request generation.

0 interrupt request generation disabled.
1 interrupt request generation enabled.

IPC_IE

Illegal Protocol Control Command Interrupt Enable — This bit controls IPC_IF interrupt request generation.
0 interrupt request generation disabled.
1 interrupt request generation enabled.

Table 26-19. PIER0 Field Descriptions (continued)

Field

Description

Summary of Contents for PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments