manualshive.com logo in svg

NXP Semiconductors PXN2020, Reference Manual, Page: 558 / 1376

Share
Download
NXP Semiconductors PXN2020 Reference Manual Download Page 558

Enhanced Direct Memory Access Controller (eDMA)

PXN20 Microcontroller Reference Manual, Rev. 1

24-38

Freescale Semiconductor

24.5.4

DMA Arbitration Mode Considerations

24.5.4.1

Fixed-Group Arbitration, Fixed-Channel Arbitration

In this mode, the channel service request from the highest priority channel in the highest priority group is 
selected to execute. If the eDMA is programmed so the channels within one group use fixed priorities, and 
that group is assigned the highest fixed priority of all groups, it is possible for that group to take all the 
bandwidth of the eDMA controller. That is, no other groups can be serviced if there is always at least one 
DMA request pending on a channel in the highest priority group when the controller arbitrates the next 
DMA request. The advantage of this scenario is that latency can be small for channels that need to be 
serviced quickly. Preemption is available in this scenario only.

DMA_MUX_CHCONFIG9_SOURCE

9

DMA_MUX.CHCONFIG9[SOURCE]

DMA MUX channel 9 source

DMA_MUX_CHCONFIG10_SOURCE

10

DMA_MUX.CHCONFIG10[SOURCE]

DMA MUX channel 10 source

DMA_MUX_CHCONFIG11_SOURCE

11

DMA_MUX.CHCONFIG11[SOURCE]

DMA MUX channel 11 source

DMA_MUX_CHCONFIG12_SOURCE

12

DMA_MUX.CHCONFIG12[SOURCE]

DMA MUX channel 12 source

DMA_MUX_CHCONFIG13_SOURCE

13

DMA_MUX.CHCONFIG13[SOURCE]

DMA MUX channel 13 source

DMA_MUX_CHCONFIG14_SOURCE

14

DMA_MUX.CHCONFIG14[SOURCE]

DMA MUX channel 14 source

DMA_MUX_CHCONFIG15_SOURCE

15

DMA_MUX.CHCONFIG15[SOURCE]

DMA MUX channel 15 source

DMA_MUX_CHCONFIG16_SOURCE

16

DMA_MUX.CHCONFIG16[SOURCE]

DMA MUX channel 16 source

DMA_MUX_CHCONFIG17_SOURCE

17

DMA_MUX.CHCONFIG17[SOURCE]

DMA MUX channel 17 source

DMA_MUX_CHCONFIG18_SOURCE

18

DMA_MUX.CHCONFIG18[SOURCE]

DMA MUX channel 18 source

DMA_MUX_CHCONFIG19_SOURCE

19

DMA_MUX.CHCONFIG19[SOURCE]

DMA MUX channel 19 source

DMA_MUX_CHCONFIG20_SOURCE

20

DMA_MUX.CHCONFIG20[SOURCE]

DMA MUX channel 20 source

DMA_MUX_CHCONFIG21_SOURCE

21

DMA_MUX.CHCONFIG21[SOURCE]

DMA MUX channel 21 source

DMA_MUX_CHCONFIG22_SOURCE

22

DMA_MUX.CHCONFIG22[SOURCE]

DMA MUX channel 22 source

DMA_MUX_CHCONFIG23_SOURCE

23

DMA_MUX.CHCONFIG23[SOURCE]

DMA MUX channel 23 source

DMA_MUX_CHCONFIG24_SOURCE

24

DMA_MUX.CHCONFIG24[SOURCE]

DMA MUX channel 24 source

DMA_MUX_CHCONFIG25_SOURCE

25

DMA_MUX.CHCONFIG25[SOURCE]

DMA MUX channel 25 source

DMA_MUX_CHCONFIG26_SOURCE

26

DMA_MUX.CHCONFIG26[SOURCE]

DMA MUX channel 26 source

DMA_MUX_CHCONFIG27_SOURCE

27

DMA_MUX.CHCONFIG27[SOURCE]

DMA MUX channel 27 source

DMA_MUX_CHCONFIG28_SOURCE

28

DMA_MUX.CHCONFIG28[SOURCE]

DMA MUX channel 28 source

DMA_MUX_CHCONFIG29_SOURCE

29

DMA_MUX.CHCONFIG29[SOURCE]

DMA MUX channel 29 source

DMA_MUX_CHCONFIG30_SOURCE

30

DMA_MUX.CHCONFIG30[SOURCE]

DMA MUX channel 30 source

DMA_MUX_CHCONFIG31_SOURCE

31

DMA_MUX.CHCONFIG31[SOURCE]

DMA MUX channel 31 source

Table 24-22. DMA Request Summary for eDMA  (continued)

DMA Request

Channel

Source

Description

Summary of Contents for PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments