manualshive.com logo in svg

NXP Semiconductors PXN2020, Reference Manual, Page: 1089 / 1376

Share
Download
NXP Semiconductors PXN2020 Reference Manual Download Page 1089

Analog-to-Digital Converter (ADC)

PXN20 Microcontroller Reference Manual, Rev. 1

Freescale Semiconductor

34-9

EDGE

Start trigger edge/ level detection. The following table shows the interaction between the EDGE bit and the 
TRGEN and EDGLEV bits. 

XSTRTEN

External Start enable. This can be used in order to synchronize the START events of two ADCs. 
0 START signal is disabled. 
1 START signal is asserted when external START is detected. 

NSTART

Normal Start conversion. Setting this bit starts the chain or scan conversion. Resetting this bit during scan 
mode causes the current chain conversion to finish, then stops the operation.
This bit stays high while the conversion is ongoing (or pending during injection mode).
0 Causes the current chain conversion to finish and stops the operation.
1 Starts the chain or scan conversion. 

JTRGEN

Injection external trigger enable.
0 External trigger disabled for channel injection (injected conversion cannot be started using an external 

signal).

1 External trigger enabled for channel injection.

JEDGE

Injection trigger edge selection. Edge selection for external trigger, if JTRGEN = 1.
0 Selects falling edge for the external trigger.
1 Selects rising edge for the external trigger.

JSTART

Injection start. Setting this bit starts the configured injected analog channels to be converted by software. 
Resetting this bit has no effect, as the injected chain conversion cannot be interrupted.

CTUEN

Cross Triggering Unit enable. 
0 The cross triggering unit is disabled and the triggered injected conversion cannot take place.
1 The cross triggering unit is enabled and the triggered injected conversion can take place.
Note: The CTU is not implemented on the PXN20.

ADCLKSEL

Analog clock frequency selector. When this bit is set, the AD_clk frequency is equal to ipg_clk frequency. 
Otherwise, the AD_clk frequency is half ipg_clk frequency. This bit can be written in Power Down mode only.
0 AD_clk frequency is half ipg_clk frequency.
1 AD_clk frequency is equal to ipg_clk frequency.

ABORTCHAIN Abort chain. When this bit is set, the ongoing Chain Conversion is aborted. This bit is reset by hardware as 

soon as a new conversion is requested.
0 Conversion is not affected.
1 Aborts the ongoing chain conversion.

ABORT

Abort conversion. When this bit is set, the ongoing conversion is aborted and a new conversion is invoked. 
This bit is reset by hardware as soon as a new conversion is invoked.
0 Conversion is not affected.
1 Aborts the ongoing conversion.

Table 34-2. MCR Field Descriptions (continued)

Field

Description

TRGEN

EDGLEV

EDGE

Trigger Detection

0

n

n

External triggering disabled

1

0

0

External trigger on falling edge of trigger

1

0

1

External trigger on rising edge of trigger

1

1

0

External trigger on low edge of trigger

1

1

1

External trigger on high edge of trigger

Summary of Contents for PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments