manualshive.com logo in svg

NXP Semiconductors PXN2020, Reference Manual, Page: 1124 / 1376

Share
Download
NXP Semiconductors PXN2020 Reference Manual Download Page 1124

Analog-to-Digital Converter (ADC)

PXN20 Microcontroller Reference Manual, Rev. 1

34-44

Freescale Semiconductor

If the content of all the injected conversion mask registers is zero (i.e., no channel is selected) the interrupt 
JECH is immediately issued after the start of conversion.

Once started, injected chain conversion cannot be interrupted.

34.4.1.5

Abort Conversion

Two different abort functions are provided.

The user can abort the ongoing conversion by setting the MCR[ABORT] bit. This results in a new start 
pulse to the analog ADC. In the case of an abort operation, the NSTART/JSTART bit remains set and the 
ABORT bit gets reset after the conversion of the next channel starts.This behavior is true for normal or 
triggered/injected conversion modes.

It is also possible to abort the current chain conversion setting the MCR[ABORTCHAIN] bit. In that case 
the behavior of the ADC depends on the MODE bit. If scan mode is disabled, the NSTART bit is 
automatically reset together with the ABORTCHAIN bit. Otherwise, if the MODE = 1, a new chain 
conversion is started.

When an ABORTCHAIN is requested while an injected conversion is running over a suspended normal 
conversion, both injected chain and normal conversion chain are aborted (both NSTART and JSTART bits 
are reset too).

34.4.2

Analog Clock Generator and Conversion Timings

The analog clock provided to the ADC module cannot be faster than 60 MHz and must have a 50% duty 
cycle. 

As shown in 

Figure 34-41

, the analog clock generator is made up of a clock prescaler and the AD_clk 

frequency is half ipg_clk frequency. When the CTU interface is enabled, depending on the position of the 
rising edge of the signal ctu_trigger (coming from the CTU), AD_clk could also be stretched as described 
in 

Figure 34-41

. 

Figure 34-41. Prescaler Simplified Block Diagram

AD_clk

ipg_clk

ctu_trigger

ipg_clk

AD_clk

 

AD_conf_latch

AD_conf_compare<1:0>

AD_conf_sample<7:0>

CTR0
CTR1
CTR2

ACKO

ipg_clk

ipg_clk/2

MCR[ADCLKSEL]

Clock

Prescaler

ctu_trigger

ADCLKSEL = 0

ipg_clk

AD_clk

ctu_trigger

ADCLKSEL = 0

Summary of Contents for PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments