manualshive.com logo in svg

NXP Semiconductors PXN2020, Reference Manual, Page: 836 / 1376

Share
Download
NXP Semiconductors PXN2020 Reference Manual Download Page 836

Enhanced Modular Input/Output Subsystem (eMIOS200)

PXN20 Microcontroller Reference Manual, Rev. 1

28-14

Freescale Semiconductor

Depending on the channel configuration it may have an internal counter or not. It means that if at least one 
mode that requires the counter is implemented, then the counter is present, otherwise it is absent.

28.3.2.8

eMIOS200 Control Register (EMIOS_CCR[n])

The control register gathers bits reflecting the status of the unified channel input/output signals and the 
overflow condition of the internal counter, as well as several read/write control bits.

Offset: UC[n] base a 0x000C

Access: User read/write

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

FREN ODIS

ODISSL

UCPRE

UC

PREN

DMA

0

IF

FCK

FEN

0

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

0

0

FORC

MA

FORC

MB

0

BSL

ED

SEL

ED

POL

MODE[0:6]

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 28-10. eMIOS200 Control Register (EMIOS_CCR[n])

Table 28-10. EMIOS_CCR[n] Field Descriptions

Field

Description

FREN

Freeze Enable Bit. The FREN bit, if set and validated by FRZ bit in EMIOS_MCR register, freezes all registers’ 
values when in debug mode, allowing the MCU to perform debug functions.
0

Normal operation.

1

Freeze unified channel registers’ values.

ODIS

Output Disable Bit. The ODIS bit allows disabling the output pin when running any of the output modes with 
the exception of GPIO mode. 
0 The output pin operates normally.
1 If the selected output disable input signal is asserted, the output pin goes to EDPOL for OPWFMB and 

OPWMB modes and to the complement of EDPOL for other modes, but the unified channel continues to 
operate normally, i.e., it continues to produce FLAG and matches. When the selected output disable input 
signal is negated, the output pin operates normally.

ODISSL

Output Disable Select Bits. The ODISSL bits select one of the four output disable input signals.

ODISSL

Input Signal

00

Output disable input 0 

01

Output disable input 1 

10

Output disable input 2 

11

Output disable input 3 

Summary of Contents for PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments