manualshive.com logo in svg

NXP Semiconductors PXN2020, Reference Manual, Page: 589 / 1376

Share
Download
NXP Semiconductors PXN2020 Reference Manual Download Page 589

Fast Ethernet Controller (FEC)

PXN20 Microcontroller Reference Manual, Rev. 1

Freescale Semiconductor

25-23

25.3.4.15 Descriptor Individual Upper Address Register (IAUR)

The IAUR is written by the user. This register contains the upper 32 bits of the 64-bit individual address 
hash table used in the address recognition process to check for possible match with the DA field of receive 
frames with an individual DA. This register is not reset and must be initialized by the user.

25.3.4.16 Descriptor Individual Lower Address (IALR)

The IALR register is written by the user. This register contains the lower 32 bits of the 64-bit individual 
address hash table used in the address recognition process to check for possible match with the DA field 
of receive frames with an individual DA. This register is not reset and must be initialized by the user.

Table 25-17. OPD Field Descriptions

Field

Description

OPCODE

Opcode field used in PAUSE frames.
These bits are a constant, 0x0001.

PAUSE_DUR

Pause duration field used in PAUSE frames.

Offset: FE 0x0118 

Access: User read/write

 

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

IADDR1

W

Reset

U

U

U

U

U

U

U

U

U

U

U

U

U

U

U

U

 16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

IADDR1

W

Reset

U

U

U

U

U

U

U

U

U

U

U

U

U

U

U

U

Figure 25-16. Descriptor Individual Upper Address Register (IAUR)

Table 25-18. IAUR Field Descriptions

Field

Descriptions

IADDR1

The upper 32 bits of the 64-bit hash table used in the address recognition process for receive frames with a 
unicast address. Bit 31 of IADDR1 contains hash index bit 63. Bit 0 of IADDR1 contains hash index bit 32.

Summary of Contents for PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments