Siemens SINAMICS S Series Скачать руководство пользователя страница 633

Страница: 633 / 1816

List of parameters

Parameters

1-633

Dependency:

Refer to: p2538

Description:

Sets the proportional gain (P gain, position loop gain, Kv factor) of the position controller.

Dependency:

Refer to: p2537, p2539, p2555, r2557, r2558

Note:

The proportional gain is used define at which traversing velocity which following error is obtained (without pre-con-
trol)

Low proportional gain:

Slow response to a setpoint - actual value difference, the following error becomes large.

High proportional gain:

Fast response to the setpoint - actual value difference, the following error becomes small.

Description:

Setting to activate the integral time of the position controller.

Value = 0 ms --> The I component of the position controller is de-activated.

Dependency:

Refer to: p2538, r2559

Description:

Sets the speed limit of the position controller output.

Dependency:

Refer to: p2541

Description:

Sets the velocity limit of the position controller output.

Dependency:

Refer to: p2541

p2538[0...n]

LR proportional gain / Kp

SERVO (Pos ctrl),
VECTOR (Pos ctrl)

Can be changed:

U, T

Calculated:

Access level:

Data type:

Floating Point

Dynamic index:

DDS, p0180

Func. diagram:

4015

P-Group:

Closed loop position control

Units group:

Unit selection:

Not for motor type:

Expert list:

Min Max

Factory

setting

0.000 [1000/min]

300.000 [1000/min]

1.000 [1000/min]

p2539[0...n]

LR integral time / Tn

SERVO (Pos ctrl),
VECTOR (Pos ctrl)

Can be changed:

U, T

Calculated:

Access level:

Data type:

Floating Point

Dynamic index:

DDS, p0180

Func. diagram:

4015

P-Group:

Closed loop position control

Units group:

Unit selection:

Not for motor type:

Expert list:

Min Max

Factory

setting

0.00 [ms]

100000.00 [ms]

0.00 [ms]

p2540

CO: LR position controller output, speed limit / LR_outp limit

SERVO (Pos ctrl),
VECTOR (Pos ctrl)

Can be changed:

U, T

Calculated:

Access level:

Data type:

Floating Point

Dynamic index:

Func. diagram:

4015

P-Group:

Closed loop position control

Units group:

3_1

Unit selection:

p0505

Not for motor type:

Expert list:

Min Max

Factory

setting

0.000 [RPM]

210000.000 [RPM]

p2540

CO: LR position controller output, velocity limit / LR_outp limit

SERVO (Lin, Pos
ctrl)

Can be changed:

U, T

Calculated:

Access level:

Data type:

Floating Point

Dynamic index:

Func. diagram:

4015

P-Group:

Closed loop position control

Units group:

4_1

Unit selection:

p0505

Not for motor type:

Expert list:

Min Max

Factory

setting

0.000 [m/min]

1000.000 [m/min]

Содержание SINAMICS S Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SINAMICS S Series

Отзывы:

Бренды по названию

Популярные бренды

Siemens SINAMICS S Series, Список руководств

Результаты поиска

Содержание SINAMICS S Series

Отзывы:

Бренды по названию

Популярные бренды