manualshive.com logo in svg

Siemens SINAMICS S Series, Список руководств

Поделиться
Скачать
Siemens SINAMICS S Series Скачать руководство пользователя страница 1539

List of faults and alarms

Faults and Alarms

3-1539

© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007

Remedy:

- if the encoder mounting was changed - re-adjust the encoder.
- replace the defective motor encoder.
- correctly set the angular commutation offset (p0431).
- correctly set the motor stator resistance, cable resistance and motor-stator leakage inductance (p0350, p0352, 
p0356).
- increase the changeover speed for the motor model (p1752). The monitoring is completely de-activated for p1752 
> p1082 (maximum speed)
Note:
For High Dynamic Motors (1FK7xxx-7xxx), for applications with a higher current, if necessary, the monitoring should 
be disabled.

F07413

Drive: Commutation angle incorrect (pole position identification)

Drive object:

SERVO, VECTOR

Reaction:

ENCODER (NONE, OFF2)

Acknowledge:

IMMEDIATELY

Cause:

An incorrect commutation angle was detected, that can result in a positive coupling in the speed controller.
- within the pole position identification routine (p1982 = 2):
A difference of > 45° electrical to the encoder angle was determined.
- for VECTOR, within the encoder adjustment (p1990 = 2):
A difference of > 6 ° electrical to the encoder angle was determined.

Remedy:

- correctly set the angular commutation offset (p0431).
- re-adjust the motor encoder after the encoder has been replaced.
- replace the defective motor encoder.
- check the pole position identification routine. If the pole position identification routine is not suitable for this motor 
type, then disable the plausibility check (p1982 = 0).

F07414 (A)

Drive: Encoder serial number changed

Drive object:

SERVO

Reaction:

ENCODER (NONE, OFF2)

Acknowledge:

IMMEDIATELY

Cause:

The serial number of the motor encoder of a synchronous motor has changed. The change was only checked for 
encoders with serial number (e.g. EnDat encoders) and build-in motors (e.g. p0300 = 401) or third-party motors 
(p0300 = 2).
Cause 1:
The encoder was replaced.
Cause 2:
A third-party, build-in or linear motor was re-commissioned.
Cause 3:
The motor with integrated and adjusted encoder was replaced.
Cause 4:
The firmware was updated to a version that checks the encoder serial number.

Remedy:

Re causes 1, 2:
Carry out an automatic adjustment using the pole position identification routine. First, accept the serial number with 
p0440 = 1. Acknowledge the fault. Initiate the pole position identification routine with p1990 = 1. Then check that the 
pole position identification routine is correctly executed.
SERVO:
If a pole position identification technique is selected in p1980, and if p0301 does not contain a motor type with an 
encoder adjusted in the factory, then p1990 is automatically activated.
or
Set the adjustment via p0431. In this case, the new serial number is automatically accepted.
or
Mechanically adjust the encoder. Accept the new serial number with p0440 = 1.
Re causes 3, 4:
Accept the new serial number with p0440 = 1.

Reaction upon A:

NONE

Acknowl. upon A:

NONE

Содержание SINAMICS S Series

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды