manualshive.com logo in svg

NXP Semiconductors MPC5566, Reference Manual

Share
Download
NXP Semiconductors MPC5566 Reference Manual Download Page 800

Enhanced Time Processing Unit (eTPU)

MPC5566 Microcontroller Reference Manual, Rev. 2

Freescale Semiconductor

18-43

18.4.6.3

eTPU Channel 

n

 Status Control Register (ETPU_C

n

SCR)

ETPU_C

n

SCR is a collection of the interrupt status bits of the channel, and also the function mode 

definition (read-write). Bits CIS, CIOS, DTRS, and DTROS for each channel can also be accessed from 
ETPU_CISR, ETPU_CIOSR, ETPU_CDTRSR, and ETPU_CDTROSR respectively. For more 
information on the three previously mentioned registers, refer to the 

eTPU Reference Manual

.

2–3

CPR

[0:1]

Channel priority. Defines the priority level for the channel. The priority level is used by the hardware scheduler. The 
values for CPR[1:0] and corresponding levels are shown in the table below.

For more information on the hardware scheduler, refer to the 

eTPU Reference Manual

.

4–6

Reserved

7

ETCS

Entry table condition select. Determines the channel condition encoding scheme that selects the entry point to be 
taken in an entry table. The ETCS value has to be compatible with the function chosen for the channel, selected in 
ETPU_C

n

CR[CFS]. Two condition encoding schemes are available.

1 Select alternate entry table condition encoding scheme.
0 Select standard entry table condition encoding scheme.For details about entry table and condition encoding 

schemes, refer to the 

eTPU Reference Manual

.

8–10

Reserved

11–15

CFS
[0:4]

Channel function select. Defines the function to be performed by the channel. The function assigned to the channel 
has to be compatible with the channel condition encoding scheme, selected by ETPU_C

n

CR[ETCS]. For more 

information about functions, refer to the 

eTPU Reference Manual

.

16

ODIS

Output disable. Enables the channel to have its output forced to the value opposite to OPOL when the output disable 
input signal corresponding to the channel group that it belongs is active.
0 Turns off the output disable feature for the channel.For more information on output disable, refer to the 

eTPU 

Reference Manual

.

1 Turns on the output disable feature for the channel

17

OPOL

Output polarity. Determines the output signal polarity. The activation of the output disable signal forces, when 
enabled by ETPU_C

n

CR[ODIS], the channel output signal to the opposite of this polarity.

0 Output active low (output disable drives output to high)
1 Output active high (output disable drives output to low)

18–20

Reserved

21–31
CPBA

[0:10]

Channel 

n

 parameter base address. The value of this field multiplied by 8 specifies the SDM parameter base host 

(byte) address for channel 

n

 (2-parameter granularity).

The formula for calculating the absolute channel parameter base (byte) address, as seen by the host, is 
eTP CPBA*8. The SDM is mirrored in the parameter sign extension (PSE) area. The formula to 
calculate the absolute channel parameter base (byte) address in the PSE area is eTP CPBA*8.
For more information on SDM addresses, refer to the 

eTPU Reference Manual

.

Table 18-25.  ETPU_C

n

CR Field Descriptions (continued)

Field

Description

CPR

Priority

00

Disabled

01

Low

10

Middle

11

High

Summary of Contents for MPC5566





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands