NXP Semiconductors MPC5566 Reference Manual Download Page 65

Page: 65 / 1268

Introduction

MPC5566 Microcontroller Reference Manual, Rev. 2

1-8

Freescale Semiconductor

— 24-bit timer resolution

— 20 KB shared code memory, 4 KB shared data memory

— Event-triggered timer subsystem

— High-level assembler and compiler

— Variable number of parameters to allocate per channel

— Double match and capture channels

— Angle clock hardware support

— Shared time or angle counter bus for all eTPU and eMIOS modules

— DMA and interrupt request support

— Nexus class 3 debug support (with some class 4 support)

•

Enhanced queued analog/digital converter (eQADC)

— Two independent ADCs with 12-bit A/D resolution

— Common mode conversion range of 0–5 V

— 40 single-ended input channels, expandable to 65 channels with external multiplexers on the

416 BGA package

— Eight channels can be used as four pairs of differential analog input channels

— 10-bit accuracy at 400 ksamples/sec., 8-bit accuracy at 800 ksamples/sec.

— Supports six FIFO queues with fixed priority

— Queue modes with priority-based preemption; initiated by software command, internal

(eTPU and eMIOS), or external triggers

— DMA and interrupt request support

— Supports all functional modes from QADC (MPC5xx family)

•

Four deserial serial peripheral interface modules (DSPI)

— Serial peripheral interface (SPI)

– Full duplex communication ports with interrupt and eDMA request support

– Supports all functional modes from QSPI submodule of QSMCM (MPC5xx family)

– Support for queues in RAM

– Six chip selects, expandable to 64 with external demultiplexers

– Programmable frame size, baud rate, clock delay, and clock phase on a per-frame basis

– Modified SPI mode for interfacing to peripherals with longer setup time requirements

— Deserial serial interface (DSI)

– Pin reduction by hardware serialization and deserialization of eTPU and eMIOS channels

– Chaining of DSI submodules

– Triggered transfer control and change in data transfer control (for reduced EMI)

•

Two enhanced serial communication interface (eSCI) modules

— UART mode provides NRZ format and half or full duplex interface

— eSCI bit rate up to 1 Mb/sec.

— Advanced error detection, and optional parity generation and detection

Summary of Contents for MPC5566





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MPC5566

Reviews:

Brands by name

Popular brands

NXP Semiconductors MPC5566, Reference Manual

Search results

Summary of Contents for MPC5566

Reviews:

Brands by name

Popular brands