manualshive.com logo in svg

NXP Semiconductors MPC5566, Reference Manual

Share
Download
NXP Semiconductors MPC5566 Reference Manual Download Page 1152

Nexus

MPC5566 Microcontroller Reference Manual, Rev. 2

Freescale Semiconductor

25-59

 

NOTE

For the e200z6 based CPU, the doubleword encoding (data size

 

= 0b000) 

indicates a doubleword access and sends out as a single data trace message 
with a single 64-bit data value. 

25.14.6.2.3

DTM Overflow Error Messages

An error message occurs when the next message is denied service because the message queue is full. The 
FIFO discards all incoming messages until the queue is completely empty. After it is empty, an error 
message is queued that indicates the message types denied into the queue while the FIFO is emptying. 

If a data trace message only attempts to enter the queue while it is emptying, the error message incorporates 
the data trace only error encoding (00010). If both OTM and data trace messages attempt to enter the 
queue, the error message incorporates the OTM and data trace error encoding (00111). If a watchpoint also 
attempts to be queued while the FIFO is being emptied, then the error message incorporates error encoding 
(01000).

NOTE

The OVC bits within the DC1 register can be set to delay the CPU to 
alleviate (but not eliminate) potential overrun situations.

Error information is messaged out in the following format:

Figure 25-45. Error Message Format

25.14.6.2.4

Data Trace Synchronization Messages

A data trace write/read with sync. message is messaged via the auxiliary port (provided data trace is 
enabled) for the following conditions (refer to 

Table 25-37

):

•

Initial data trace message after exit from system reset or whenever data trace is enabled

•

Upon exiting debug mode

•

After occurrence of queue overrun (can be caused by any trace message), provided data trace is 
enabled

•

After the periodic data trace counter has expired indicating 255 

without-sync

 data trace messages 

have occurred since the last 

with-sync

 message occurred

•

Upon assertion of the event in (EVTI) pin, the first data trace message is a synchronization message 
if the EIC bits of the DC1 register have enabled this feature

•

Upon data trace write/read after the previous DTM message was lost due to an attempted access to 
a secure memory location

DATA

MSB

LSB

2

3

4

U-ADDR

DSZ

SRC

5

4 bits

1

TCODE (000110)

3 bits

1

–

32 bits

1

–

64 bits

6 bits

Max length = 109 bits; Min length = 15 bits

Summary of Contents for MPC5566





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands