manualshive.com logo in svg

NXP Semiconductors MPC5566, Reference Manual

Share
Download
NXP Semiconductors MPC5566 Reference Manual Download Page 671

Boot Assist Module (BAM)

MPC5566 Microcontroller Reference Manual, Rev. 2

16-12

Freescale Semiconductor

 

If serial boot mode is entered indirectly from external boot/single-master or external 
boot/multi-master/external arbitration because no valid RCHW was found, then the MMU and EBI are 
configured the for an external boot mode with a 16-bit data bus. 

Refer to 

Table 16-3

 and 

Table 16-5

 for more information. 

16.3.2.3.2

Serial Boot Mode FlexCAN and eSCI Configuration

In serial boot mode, the BAM program configures FlexCAN A and eSCI A to receive messages. The 
CNRXA and RXDA signals are configured as inputs to the FlexCAN and eSCI modules. The CNTXA 
signal is configured as an output from the FlexCAN module. The TXDA signal of the eSCI A remains 
configured as GPIO input. The BAM program writes 0x0000_0000_0000_0000 to the e200z6 core 
timebase registers (TB), enables the e200z6 core setting the watchdog timer to use 2.5 

×

 2

27

 

system clock 

cycles before a reset occurs. 

Refer to for examples of time out periods.

In serial boot mode the FlexCAN controller is configured to operate at a baud (bit) rate equal to the system 
clock frequency divided by 60 with one message buffer (MB) using the standard 11-bit identifier format 
detailed in the CAN 2.0A specification. 

Refer to 

Section 22.4.5.4, “Protocol Timing

,” for information on FlexCAN bit rate generation.

Coming out of reset, the default system clock is 1.5 times the crystal frequency. The baud rate with PLL 
enabled is equal to the crystal frequency divided by 40. 

Refer to 

Chapter 11, “Frequency Modulated Phase Locked Loop and System Clocks (FMPLL)

,” for more 

information. 

Table 16-7

 shows FlexCAN operation at reset.

The BAM ignores the following errors:

•

Bit 1 errors

•

Bit 0 errors

•

Acknowledge errors

•

Cyclic redundancy code errors

•

Form  errors

•

Stuffing errors

•

TX error counter errors

Table 16-7. BAM FlexCAN Frequency at Reset (FMPLL Enabled out of Reset) 

FMPLL Clock Mode

System Clock Frequency (f

sys

) 

after Reset

Serial Boot Mode Frequency

1

(FlexCAN Baud Rate) 

1

Serial boot mode frequency is set in software as the system clock frequency divided by 60.

Crystal reference mode or 
External reference mode

1.5 x crystal reference frequency 

(f

ref_crystal

) 

2

 

2

Crystal reference frequency is set at 8–20 MHz.

Crystal reference frequency 

÷

 40 

Dual controller mode

2 x EXTCLK

EXTCLK 

÷

 30 

Summary of Contents for MPC5566





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands