Freescale Semiconductor MPC5565 Reference Manual Download Page 665 | Manualshive

Page: 665 / 1153

background image

Enhanced Time Processing Unit (eTPU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

17-10

Freescale Semiconductor

•

Resource sharing features resolve channel contention for common use of channel registers,
memory and microengine time

— Hardware scheduler works as a ‘task management’ unit, dispatching event service routines by

predefined, host-configured priority.

— Hardware breakpoints on data access, qualified by address and/or data values.

— Hardware breakpoints on instruction address.
— Automatic channel context switch when a ‘task switch’ occurs; that is, one function thread ends

and another begins to service a request from another channel. Channel-specific registers, flags
and parameter base address are automatically loaded for the next serviced channel.

— Individual channel priority setting in three levels: high, middle, and low.

— Scheduler priority scheme allows calculation of worst case latency for event servicing and

ensures servicing of all channels by preventing permanent blockage.

— SDM shared between host core and both eTPU engines, supporting channel-channel or

host-channel communication.

— Hardware implementation of four semaphores allows for resource arbitration between channels

in both eTPU engines.

— Hardware semaphores are directly supported by the microengine instruction set.

— Dual-parameter coherency hardware support allows coherent (to host) access to 2 parameters

by microengines in back-to-back accesses.

— Coherent dual-parameter controller allows coherent (to microengines) accesses to two

parameters by the host.

•

Test and development support features

— Nexus level 3 debug support through the eTPU Nexus block (NDEDI)

— Software breakpoints

— SCM (code memory) continuous signature-check built-in code integrity test multiple input

signature calculator (MISC): runs concurrently with eTPU normal operation

17.2

Modes of Operation

The eTPU is capable of working in the following modes.

17.2.1

User Configuration Mode

By having access to the shared code memory (SCM), the core has the ability to program the eTPU cores
with time functions.

17.2.2

User Mode

In user mode the core does not access the eTPU shared code memory, and pre-defined eTPU functions are
used.

«
...
663
664
665
666
667
...
»

Summary of Contents for MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5565

Brand: Ubisys Pages: 2

Brand: FAAC Pages: 44

Brand: Faulhaber Pages: 66

Brand: M-system Pages: 103

Brand: M-system Pages: 18

Brand: Full Gauge Controls Pages: 3

Freedom Bridge FB3

Brand: Identiv Pages: 2

Brand: GEM Pages: 17

Brand: AirCycler Pages: 2

Torque Converter Lock-Up

Brand: TS Performance Pages: 4

Brand: ISVT Pages: 78

Brand: Linear Technology Pages: 8

Brand: Barco Pages: 4

Brand: Vageo Pages: 2

Brand: DirectConnect Pages: 2

Driver VISIO IoT

Brand: Sulion Pages: 8

Brand: Sentiotec Pages: 92

Brand: Sorel Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands