Freescale Semiconductor MPC5565 Reference Manual Download Page 180 | Manualshive

Page: 180 / 1153

background image

System Integration Unit (SIU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

6-5

6.2.1.2

Reset Output (RSTOUT)

RSTOUT is an active-low output signal that uses a push/pull configuration. It is driven to the low state by
the MCU for all internal and external reset sources. After the RESET input signal negates, RSTOUT
asserts for:

•

16000 clock cycles for devices configured in bypass mode

•

16004 clock cycles for devices configured for FMPLL dual-controller mode (1:1)

•

2404 clock cycles for all other FMPLL modes

To invoke an external software reset, write a 1 to the system external reset (SER) bit in the system reset
control register (SIU_SRCR). This asserts RSTOUT for 2400 clock cycles. An external software reset
does not execute the BAM module or sample BOOTCFG[0:1].

6.2.1.3

General-Purpose I/O (GPIO[0:213])

The GPIO signals provide general-purpose input and output functions. GPIO signals are generally
multiplexed with other I/O pin functions. Each GPIO input and output is separately controlled by an
eight-bit general-purpose data input (SIU_GPDI

n

) and a general-purpose data output (SIU_GPDO

n

)

register.

Refer to the following sections for more information:

Section 6.3.1.151, “GPIO Pin Data Output Registers 0–213 (SIU_GPDOn)

Section 6.3.1.152, “GPIO Pin Data Input Registers 0–213 (SIU_GPDIn)

6.2.1.4 Boot Configuration (BOOTCFG[0:1])

The BOOTCFG value specifies the location and boot mode used by the boot assist module (BAM). All
reset sources can read the boot configuration field, BOOTCFG[0:1], except a debug port reset and a
software external reset.

The BOOTCFG values are read only if RSTCFG asserts while RSTOUT is asserted. The BOOTCFG
signal asserts after RSTCFG to get the boot input information. BOOTCFG[0:1] is sampled four clock
cycles before RSTOUT negates, and the latched boot values are stored in the reset status register
(SIU_RSR).

If RSTCFG asserts while processing a reset, BOOTCFG[0:1] is sampled. Otherwise, if RSTCFG negates
while processing a reset, the following occurs:

1. BOOTCFG[0:1] is not sampled

2. BAM module boots from internal flash (default = 0b00)

3. Boot value from internal flash is written to BOOTCFG[0:1] field in the reset status register

(SIU_RSR)

4. BOOTCFG[0:1] values are latched and driven as output signals from the SIU

«
...
178
179
180
181
182
...
»

Summary of Contents for MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5565

Brand: Wasp Pages: 16

Brand: T-Verter Pages: 121

Brand: Happy Pages: 10

Brand: 3M Pages: 34

Brand: Danfoss Pages: 7

coviva Smartbox TKP100A

Brand: hager Pages: 45

Brand: mikroElektronika Pages: 3

Brand: Window Master Pages: 7

Brand: phytron Pages: 55

Brand: MacroAir Technologies Pages: 32

Brand: A & H Pages: 35

MEMO CORE CONTROL

Brand: MegaLite Pages: 11

Brand: Danfoss Pages: 4

Enclosure ENCR-10

Brand: suprema Pages: 18

Brand: Cypress Pages: 13

SoundLinQ SL2xD2

Brand: Vais Technology Pages: 21

EscapeKeeper JR

Brand: Fright Ideas Pages: 2

Brand: LTH Electronics Pages: 266

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands