manualshive.com logo in svg

Freescale Semiconductor MPC5565, Reference Manual

The Freescale Semiconductor MPC5565 Reference Manual is a comprehensive guide for users looking to maximize the performance of this powerful microcontroller. This manual can be downloaded for free from our website, providing detailed instructions and essential information for users. Unlock the full potential of your MPC5565 with this invaluable resource.

Share
Download
background image

e200z6 Core Complex

MPC5565 Microcontroller Reference Manual, Rev. 1.0

3-28

Freescale Semiconductor

 

3.3.2.6

L1 Cache Configuration Register 0 (L1CFG0)

The L1 cache configuration register 0 (L1CFG0) is a 32-bit read-only register. L1CFG0 provides 
information about the configuration of the L1 cache design. The contents of the L1CFG0 register can be 
read using a 

mfspr 

instruction. The SPR number for L1CFG0 is 515 in decimal. The L1CFG0 register is 

shown in 

Figure 3-17

.

23

CLFC

 Cache lock bits flash clear
When written to a 1, a cache lock bits flash clear operation is initiated by hardware. 

After this is complete, this bit is reset to 0. Writing a 1 while a flash clear 
operation is in progress will result in an undefined operation. Writing a 0 to this 
bit while a flash clear operation is in progress will be ignored. Cache lock bits 
flash clear operations require approximately cycles to complete. Clearing occurs 
regardless of the enable (CE) value.

24:28

—

Reserved

29

CABT

Cache operation aborted
Indicates a cache invalidate or a cache lock bits flash clear operation was aborted 

prior to completion. This bit is set by hardware on an aborted condition, and will 
remain set until cleared by software writing 0 to this bit location.

30

CINV

Cache invalidate

0 = No cache invalidate
1 = Cache invalidation operation

When written to a 1, a cache invalidation operation is initiated by hardware. After 
this is complete, this bit is reset to 0. Writing a 1 while an invalidation operation is in 
progress will result in an undefined operation. Writing a 0 to this bit while an 
invalidation operation is in progress will be ignored. Cache invalidation operations 
require approximately cycles to complete. Invalidation occurs regardless of the 
enable (CE) value.

31

CE

Cache Enable

0 = Cache is disabled
1 = Cache is enabled

When disabled, cache lookups are not performed for normal load or store accesses.
Other L1CSR0 cache control operations are still available. Also, operation of the 
store buffer is not affected by CE.

CAR

CH 

CWP

A

CF

AHA

CFISW

A

 

0

CBSIZE 

CREPL

CLA

CP

A

CNW

A

Y

 

CSIZE 

0

1

2

3

4

5

6

7

8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

01

1

0

1

0

0

00

10

1

1

00000001 (2 way)

00000001000 (8 KB) 

SPR - 515; Read-only 

Figure 3-17. L1 Cache Configuration Register 0 (L1CFG0)

Table 3-9. L1CSR0 Field Descriptions (continued)

Bits

Name

Description

Summary of Contents for MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5565

ABB ACS880 Series Supplement Manual preview
ACS880 Series
Brand: ABB Pages: 50
Cansec H1000 Installation Manual And Instructions For Use preview
H1000
Brand: Cansec Pages: 45
Cansec CP40 Installation Manual preview
CP40
Brand: Cansec Pages: 43
Cansec MAP2 Installation Manual preview
MAP2
Brand: Cansec Pages: 32
Danfoss VLT MCD 200 Installation Manual preview
VLT MCD 200
Brand: Danfoss Pages: 32
Danfoss VLT AutomationDrive FC 360 Programming Manual preview
VLT AutomationDrive FC 360
Brand: Danfoss Pages: 60
Danfoss AMV 110 NL AQT Datasheet preview
AMV 110 NL AQT
Brand: Danfoss Pages: 4
Danfoss ECL Comfort 110 Quick Manual preview
ECL Comfort 110
Brand: Danfoss Pages: 2
QED MP50 Instruction Manual preview
MP50
Brand: QED Pages: 26
Rain Bird Image Series Quick Start Manual preview
Image Series
Brand: Rain Bird Pages: 4
Rain Bird ESP-ME3 Quick Reference Manual preview
ESP-ME3
Brand: Rain Bird Pages: 2
Rain Bird ESP-Me User Manual preview
ESP-Me
Brand: Rain Bird Pages: 140
Raindrip WeatherSmart RSC600i Installation & Programming preview
WeatherSmart RSC600i
Brand: Raindrip Pages: 36
Walchem WebMaster Manual preview
WebMaster
Brand: Walchem Pages: 2
Walchem WebMaster Quick Start Manual preview
WebMaster
Brand: Walchem Pages: 73
Walchem W900 Series Instruction Manual preview
W900 Series
Brand: Walchem Pages: 126
Yamaha RCX340 Service Information preview
RCX340
Brand: Yamaha Pages: 5
Cypress CY3280-BK1 Quick Start Manual preview
CY3280-BK1
Brand: Cypress Pages: 3

Brands by name

Popular brands

Load more brands