Freescale Semiconductor MPC5565 Reference Manual Download Page 972 | Manualshive

Page: 972 / 1153

background image

Preface

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

21-35

21.5.2

FlexCAN2 Addressing and RAM Size

There are 1024 bytes of RAM for a maximum of 64 message buffers. The user can program the maximum
number of message buffers (MBs) using the MAXMB field in the CAN

x

_MCR. For this 1024-byte RAM

configuration, MAXMB can be any number from 0

–

63.

21.6

Document Revision History

Table 21-19. Changes Between MPC5565RM Revisions 0.1 and 1

In the Receive Process, Section 21.4.3, “Receive Process,” in the third step, changed
“receive active and empty” to EMPTY.

Reworded the first paragraph of Matching Process, Section 21.4.3.1, “Matching Process:”
• From: “After a MB is marked as ‘RX active and empty,’ it will participate in the internal matching process, which takes place

every time the receiver receives an error free frame. In this process, all active RX buffers compare their ID value to the
newly received one, and if a match occurs, the frame is transferred (move in) to the first (that is, lowest entry) matching MB.”

• To: “The matching process compares the IDs of all active RX message buffers to newly received frames, so that, if a match

occurs, a newly received frame is transferred (moved in) to the first (that is, lowest entry) matching MB. Only MBs marked
as EMPTY, FULL, or OVERRUN will participate in the internal matching process at the CRC frame field. The internal
matching process takes place every time the receiver receives an error free frame.”

• In Bus Interface, Section 21.4.8, “Bus Interface,” the following NOTE has been added:

“Unused MB space must not be used as general purpose RAM while FlexCAN is transmitting and receiving CAN

frames.”

Table 21-4

Message Buffer Field Descriptions

: Changed description of the ID field to match register diagram. Changed (28 to

11) to (3 to 13) for the MSB bits and added (14 to 31) for the LSB bits:

Standard frame format, only the 11 most significant bits (3 to 13) are used for frame identification in both receive and

transmit cases. The 18 least significant bits (14 to 31) are ignored.

Extended frame format, all bits are used for frame identification in both receive and transmit cases.

Section 21.3.3.2, “Control Register (CANx_CR): Deleted the following sentence
• Most of the fields in this register should only be changed while the module is disabled or in freeze mode.
• Table 21-8: CANx_CR Field Descriptions: Deleted from field description for CLK_SRC: To guarantee reliable operation, this

bit should only be changed while the module is disabled.

«
...
970
971
972
973
974
...
»

Summary of Contents for MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5565

Brand: Tapeswitch Pages: 13

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 20

Brand: UniKey Pages: 20

Brand: Garmin Pages: 4

Brand: Samson Pages: 6

Brand: L-Acoustics Pages: 20

Brand: YASKAWA Pages: 121

Brand: YASKAWA Pages: 17

Brand: YASKAWA Pages: 30

Brand: Full Gauge Controls Pages: 3

Brand: Linear Technology Pages: 32

Ambience Control 1

Brand: EuroLite Pages: 20

Brand: SKF Pages: 88

Brand: Netro Pages: 14

SMARC conga-SMX8-X

Brand: Congatec Pages: 8

Brand: MT-Propeller Pages: 16

PMC 1204 Series

Brand: Curtis Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands