manualshive.com logo in svg

Freescale Semiconductor MPC5565, Reference Manual

The Freescale Semiconductor MPC5565 Reference Manual is a comprehensive guide for users looking to maximize the performance of this powerful microcontroller. This manual can be downloaded for free from our website, providing detailed instructions and essential information for users. Unlock the full potential of your MPC5565 with this invaluable resource.

Share
Download
background image

Flash Memory

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

13-9

 

16

EER

ECC event error. Provides information on previous reads; if a double bit detection occurred, the EER bit is set 
to 1. This bit must then be cleared, or a reset must occur before this bit returns to a 0 state. This bit cannot 
be set by the application. In the event of a single bit detection and correction, this bit is not set. If EER is not 
set, or remains 0, this indicates that all previous reads (from the last reset, or clearing of EER) were correct.   
Since this bit is an error flag, it must be cleared to a 0 by writing a 1 to the register location. A write of 0 has 
no effect.
0 Reads are occurring normally.
1 An ECC Error occurred during a previous read.

Note:

This bit can be set on speculative prefetches that cause double bit error detection. Therefore, use the 
ECSM[FNCE] flag for detecting non-correctable ECC errors in the flash instead of using 
FLASH_MCR[EER].

17

RWE

Read while write event error. Provides information on previous RWW reads. If a read while write error occurs, 
this bit is set to 1. This bit must then be cleared, or a reset must occur before this bit returns to a 0 state. This 
bit cannot be set to 1 by the user. If RWE is not set, or remains 0, this indicates that all previous RWW reads 
(from the last reset, or clearing of RWE) were correct. Since this bit is an error flag, it must be cleared to a 0 
by writing a 1 to the register location. A write of 0 has no effect.
0 Reads are occurring normally.
1 A read while write error occurred during a previous read.

18–19

Reserved.

20

PEAS

Program/erase access space. Indicates which space is valid for program and erase operations, either main 
array space or shadow space. PEAS is read only. 
0 Shadow address space is disabled for program/erase and main address space enabled
1 Shadow address space is enabled for program/erase and main address space disabled.

21

DONE

State machine status. Indicates if the flash module is performing a high voltage operation. DONE is set to a 
1 on termination of the flash module reset and at the end of program and erase high voltage sequences. 
0 Flash is executing a high voltage operation.
1 Flash is not executing a high voltage operation.

22

PEG

Program/erase good. Indicates the completion status of the last flash program or erase sequence for which 
high voltage operations were initiated. The value of PEG is updated automatically during the program and 
erase high voltage operations. Aborting a program/erase high voltage operation causes PEG to be cleared, 
indicating the sequence failed. PEG is set to a 1 when the module is reset. PEG is read only.

The value of PEG is valid only when PGM = 1 and/or ERS = 1 and after DONE has transitioned from 0 to 1 
due to an abort or the completion of a program/erase operation. PEG is valid until PGM/ERS makes a 1 to 0 
transition or EHV makes a 0 to 1 transition. The value in PEG is not valid after a 0 to 1 transition of DONE 
caused by PSUS or ESUS being set to logic 1. A diagram presenting PEG valid times is presented in 

Figure 13-5

. If PGM and ERS are both 1 when DONE makes a qualifying 0 to 1 transition the value of PEG 

indicates the completion status of the PGM sequence. This happens in an erase-suspended program 
operation.
0 Program or erase operation failed.
1 Program or erase operation successful.

23–24

Reserved.

25

STOP

Stop mode enabled. Puts the flash into stop mode. Changing the value in STOP from a 0 to a 1 places the 
flash module in stop mode. A 1 to 0 transition of STOP returns the flash module to normal operation. STOP 
can be written only when PGM and ERS are low. When STOP = 1, only the STOP bit in the MCR can be 
written. In STOP mode all address spaces, registers, and register bits are deactivated except for the 
FLASH_MCR[STOP] bit. 

0 Flash is not in stop mode; the read state is active.
1 Flash is in stop mode.

Table 13-5. FLASH_MCR Field Descriptions (continued)

Field

Description

Summary of Contents for MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5565

FAAC 740 D User Manual preview
740 D
Brand: FAAC Pages: 64
M-Audio Axiom AIR 25 Service Manual preview
Axiom AIR 25
Brand: M-Audio Pages: 26
M Climate Bobbie Installation Instructions Manual preview
Bobbie
Brand: M Climate Pages: 12
Parker ACR7000 Series Hardware Manual preview
ACR7000 Series
Brand: Parker Pages: 21
Parker AC890PX Series Quick Start Manual preview
AC890PX Series
Brand: Parker Pages: 26
Vageo DT-1 Manual preview
DT-1
Brand: Vageo Pages: 2
Taco Electronic Solutions iWorx MPU2 Installation Manual preview
iWorx MPU2
Brand: Taco Electronic Solutions Pages: 28
Zander Aachen ZX09 Series Operating Manual preview
ZX09 Series
Brand: Zander Aachen Pages: 75
LEGRAND MRD6 v2 Installation Instructions Manual preview
MRD6 v2
Brand: LEGRAND Pages: 10
zeeltronic PDCI-24V User Manual preview
PDCI-24V
Brand: zeeltronic Pages: 13
QD Dynamics Pi HSC505-32 User'S Information Manual preview
Pi HSC505-32
Brand: QD Dynamics Pages: 64
VDH ALFANET 1-LS User Manual preview
ALFANET 1-LS
Brand: VDH Pages: 4
VIRDI AC-2200 User Manual preview
AC-2200
Brand: VIRDI Pages: 73
TAC Vista TAC Xenta OP Manual preview
TAC Xenta OP
Brand: TAC Vista Pages: 2
Ellard V3D Maxi Product Instructions preview
V3D Maxi
Brand: Ellard Pages: 21
ICP DAS USA ISaGRAF mPAC Series Getting Started preview
ISaGRAF mPAC Series
Brand: ICP DAS USA Pages: 75
Texas Instruments TIDA-00830 Quick Start Manual preview
TIDA-00830
Brand: Texas Instruments Pages: 6
Eaton FC6 User Manual preview
FC6
Brand: Eaton Pages: 10

Brands by name

Popular brands

Load more brands