manualshive.com logo in svg

Freescale Semiconductor MPC5565, Reference Manual

The Freescale Semiconductor MPC5565 Reference Manual is a comprehensive guide for users looking to maximize the performance of this powerful microcontroller. This manual can be downloaded for free from our website, providing detailed instructions and essential information for users. Unlock the full potential of your MPC5565 with this invaluable resource.

Share
Download
background image

Preface

MPC5565 Microcontroller Reference Manual, Rev. 1.0 

21-10

Freescale Semiconductor

 

Table 21-7. CAN

x

_MCR Field Descriptions

Field

Description

0

MDIS

Module disable. Controls whether FlexCAN2 is enabled or not. When disabled, FlexCAN2 shuts down the 
clock to the CAN protocol interface and message buffer management submodules. This is the only bit in 
CAN

x

_MCR not affected by soft reset. Refer to 

Section 21.4.6.2, “Module Disabled Mode

,” for more 

information.
0 Enable the FlexCAN2 module
1 Disable the FlexCAN2 module

1

FRZ

Freeze enable. Specifies the FlexCAN2 behavior when the HALT bit in the CAN

x

_MCR is set or when debug 

mode is requested at MCU level. When FRZ is asserted, FlexCAN2 is enabled to enter freeze mode. 
Negation of this bit field causes FlexCAN2 to exit from freeze mode.
0 Not enabled to enter freeze mode
1 Enabled to enter freeze mode

2

Reserved.

3

HALT

Halt FlexCAN. Assertion of this bit puts the FlexCAN2 module into freeze mode if FRZ is asserted. The CPU 
should clear it after initializing the message buffers and CAN

x

_CR. If FRZ is set, no reception or transmission 

is performed by FlexCAN2 before this bit is cleared. While in freeze mode, the CPU has write access to the 
CAN

x

_ECR, that is otherwise read-only. Freeze mode cannot be entered while FlexCAN2 is disabled. Refer 

to 

Section 21.4.6.1, “Freeze Mode

,” for more information.

0 No freeze mode request.
1 Enters freeze mode if the FRZ bit is asserted.

4

NOTRDY

FlexCAN2 not ready. Indicates that FlexCAN2 is either disabled or in freeze mode. It is negated after 
FlexCAN2 has exited these modes.
0 FlexCAN2 module is either in normal mode, listen-only mode or loop-back mode
1 FlexCAN2 module is either disabled or freeze mode

5

Reserved.

6

SOFTRST

Soft reset. When asserted, FlexCAN2 resets its internal state machines and some of the memory-mapped 
registers. The following registers are affected by soft reset: 
  • CAN

x

_MCR (except the MDIS bit), 

  • CAN

x

_TIMER, 

  • CAN

x

_ECR, 

  • CAN

x

_ESR, 

  • CAN

x

_IMRL, 

  • CAN

x

_IMRH, 

  • CAN

x

_IFRL, 

  • CAN

x

_IFRH. 

Configuration registers that control the interface to the CAN bus are not affected by soft reset. The following 
registers are unaffected: 
 • CANx_CR 
  • CAN

x

_RXGMASK 

  • CAN

x

_RX14MASK 

  • CAN

x

_RX15MASK

 • all Message buffers
The SOFTRST bit can be asserted directly by the CPU when it writes to the CAN

x

_MCR, but it is also 

asserted when global soft reset is requested at MCU level. Because soft reset is synchronous and has to 
follow a request/acknowledge procedure across clock domains, it may take some time to fully propagate its 
effect. The SOFTRST bit remains asserted while reset is pending, and is automatically negated when reset 
completes. Therefore, software can poll this bit to know when the soft reset has completed. 
0 No reset request
1 Resets values in registers indicated above.

Summary of Contents for MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5565

Raymarine P70 Quick Reference preview
P70
Brand: Raymarine Pages: 12
Lattice Semiconductor HDR-60 User Manual preview
HDR-60
Brand: Lattice Semiconductor Pages: 26
Radware Alteon Installation And Maintenance Manual preview
Alteon
Brand: Radware Pages: 98
Zander Aachen SCB Series Operating Instructions Manual preview
SCB Series
Brand: Zander Aachen Pages: 44
Zamel Extra Free ROB-01/12-24V Manual Instruction preview
Extra Free ROB-01/12-24V
Brand: Zamel Pages: 2
Sparkfun Electronics Explorer Dongle Manual preview
Explorer Dongle
Brand: Sparkfun Electronics Pages: 16
Lumel re72 series Quick Start Manual preview
re72 series
Brand: Lumel Pages: 32
ProMinent DCM 5 Series Quick Start Manual preview
DCM 5 Series
Brand: ProMinent Pages: 2
Omega Engineering PHCN-410 Operator'S Manual preview
PHCN-410
Brand: Omega Engineering Pages: 11
Velleman-Kit EDU01 Manual preview
EDU01
Brand: Velleman-Kit Pages: 32
Doepke RJSG 1 Installation And Operating Manual preview
RJSG 1
Brand: Doepke Pages: 2
Leader F1620 Manual preview
F1620
Brand: Leader Pages: 46
Taconova Tacosol Load EXA L Manual preview
Tacosol Load EXA L
Brand: Taconova Pages: 40
Cypress CY3250-PLC20QFN Quick Start Manual preview
CY3250-PLC20QFN
Brand: Cypress Pages: 2
Vais Technology SoundLinQ SL2xD2 Owner'S Manual preview
SoundLinQ SL2xD2
Brand: Vais Technology Pages: 21
Bettis GVO-C Series Operation And Maintenance Manual preview
GVO-C Series
Brand: Bettis Pages: 14
Hubbell Electric Fire Pump Controllers LXi-2400 Specifications preview
Electric Fire Pump Controllers LXi-2400
Brand: Hubbell Pages: 2
Unitech UT-102 Instruction Manual preview
UT-102
Brand: Unitech Pages: 15

Brands by name

Popular brands

Load more brands