manualshive.com logo in svg

Freescale Semiconductor MPC5565, Reference Manual

The Freescale Semiconductor MPC5565 Reference Manual is a comprehensive guide for users looking to maximize the performance of this powerful microcontroller. This manual can be downloaded for free from our website, providing detailed instructions and essential information for users. Unlock the full potential of your MPC5565 with this invaluable resource.

Share
Download
background image

Enhanced Direct Memory Access (eDMA)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

9-11

Both the DMA request input signal and this enable request flag must be asserted before a channel’s 
hardware service request is accepted. The state of the eDMA enable request flag does 

not

 affect a channel 

service request made explicitly through software or a linked channel request.

As a given channel completes the processing of its major iteration count, there is a flag in the transfer 
control descriptor that can affect the ending state of the EDMA_ERQR bit for that channel. If the 
TCD.D_REQ bit is set, then the corresponding EDMA_ERQR bit is cleared after the major loop is 
complete, disabling the DMA hardware request. Otherwise if the D_REQ bit is cleared, the state of the 
EDMA_ERQR bit is unaffected.

9.2.2.4

eDMA Enable Error Interrupt Register (EDMA_EEIRL)

The EDMA_EEIRL provides a bit map for the 32 channels to enable the error interrupt signal for each 
channel. EDMA_EEIRL maps to channels 31-0.

The state of any given channel’s error interrupt enable is directly affected by writes to these registers; it is 
also affected by writes to the EDMA_SEEIR and EDMA_CEEIR. The EDMA_SEEIR and 
EDMA_CEEIR are provided so that the error interrupt enable for a 

single

 channel can easily be modified 

without the need to perform a read-modify-write sequence to the EDMA_EEIRL.

Both the DMA error indicator and this error interrupt enable flag must be asserted before an error interrupt 
request for a given channel is asserted.

Address: Base + 0x000C

Access: User R/W

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R ERQ

31

ERQ

30

ERQ

29

ERQ

28

ERQ

27

ERQ

26

ERQ

25

ERQ

24

ERQ

23

ERQ

22

ERQ

21

ERQ

20

ERQ

19

ERQ

18

ERQ

17

ERQ

16

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R ERQ

15

ERQ

14

ERQ

13

ERQ

12

ERQ

11

ERQ

10

ERQ

09

ERQ

08

ERQ

07

ERQ

06

ERQ

05

ERQ

04

ERQ

03

ERQ

02

ERQ

01

ERQ

00

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 9-4. eDMA Enable Request Low Register (EDMA_ERQRL) 

Table 9-4. EDMA_ERQRL Field Descriptions

Field

Description

0–31

ERQ

n

Enable DMA hardware service request 

n.

0 The DMA request signal for channel n is disabled.
1 The DMA request signal for channel n is enabled.

Summary of Contents for MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5565

Campbell CR10 PROM Replacement Procedure preview
CR10 PROM
Brand: Campbell Pages: 8
Parkside PDWE 8 A1 Instructions Manual preview
PDWE 8 A1
Brand: Parkside Pages: 86
Audioaccess PX-700 Manual preview
PX-700
Brand: Audioaccess Pages: 2
AirCycler SmartExhaust Manual preview
SmartExhaust
Brand: AirCycler Pages: 2
TS Performance Torque Converter Lock-Up Manual preview
Torque Converter Lock-Up
Brand: TS Performance Pages: 4
Grundfos EC 15 Installation And Operating Instructions Manual preview
EC 15
Brand: Grundfos Pages: 80
YASKAWA Z1000U Series Quick Start Manual preview
Z1000U Series
Brand: YASKAWA Pages: 92
Casambi CBU-PWM4-4 Manual preview
CBU-PWM4-4
Brand: Casambi Pages: 4
RADEMACHER Troll Comfort Instruction Manual For The Electrical Connection And For Commissioning preview
Troll Comfort
Brand: RADEMACHER Pages: 112
Newport i/8 Quick Start preview
i/8
Brand: Newport Pages: 2
RADIKAL TECHNOLOGIES SAC-2K Manual preview
SAC-2K
Brand: RADIKAL TECHNOLOGIES Pages: 36
Evoqua WALLACE & TIERNAN MULTI-FUNCTIONS-CONTROLLER Short Operating Instructions preview
WALLACE & TIERNAN MULTI-FUNCTIONS-CONTROLLER
Brand: Evoqua Pages: 4
OK-I PTZ-KB050 Operational Manual preview
PTZ-KB050
Brand: OK-I Pages: 10
AudioCodes Mediant 4000B SBC Hardware Installation Manual preview
Mediant 4000B SBC
Brand: AudioCodes Pages: 60
Atmel AVR461 Quick Start Manual preview
AVR461
Brand: Atmel Pages: 16
ELMARK CD-701 Instructions For Installation And Use Manual preview
CD-701
Brand: ELMARK Pages: 7
S&C GridMaster Installation Manual preview
GridMaster
Brand: S&C Pages: 16
Astrapool LumiPlus Quick Start Manual preview
LumiPlus
Brand: Astrapool Pages: 2

Brands by name

Popular brands

Load more brands