manualshive.com logo in svg

Freescale Semiconductor MPC5565, Reference Manual

The Freescale Semiconductor MPC5565 Reference Manual is a comprehensive guide for users looking to maximize the performance of this powerful microcontroller. This manual can be downloaded for free from our website, providing detailed instructions and essential information for users. Unlock the full potential of your MPC5565 with this invaluable resource.

Share
Download
background image

System Integration Unit (SIU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

6-30

Freescale Semiconductor

6.3.1.19

Pad Configuration Registers 28–43 (SIU_PCR28–SIU_PCR43)

The SIU_PCR28–SIU_PCR43 registers control the function, direction, and electrical attributes of 
DATA[0:15]_GPIO[28:43].

Figure 6-20. DATA[0:15]_GPIO[28:43] Pad Configuration Registers (SIU_PCR28–SIU_PCR43)

6.3.1.20

Pad Configuration Registers 44–48 (SIU_PCR44–SIU_PCR48)

The SIU_PCR44–SIU_PCR48 register controls the function, direction, and electrical attributes of 
DATA[16:20]_GPIO[44:48].

Figure 6-21. DATA[16:20]_GPIO[44:48] Pad Configuration Registers (SIU_PCR44–SIU_PCR48)

Address: Base + 0x0078 through Base + 0x0096

Access: R/W

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

0

0

0

0

0

PA

OBE

1

1

When configured as DATA[0:15], the OBE bit has no effect. When configured as GPDO, set the OBE bit to 1.

IBE

2

2

When configured as DATA[0:15] or GPDO, set the IBE bit to 1 to reflect the pin state in the GPDI register. 
Clear the IBE to 0 to reduce power consumption. When configured as GPDI, set the IBE bit to 1.

DSC

ODE

3

3

When configured as DATA[0:15], clear the ODE bit to 0.

HYS

4

4

If external master operation is enabled, clear the HYS bit to 0. 

0

0

WPE

5

5

Refer to the EBI section for weak pullup settings when configured as DATA[0:15].

WPS

5

W

RESET:

0

0

0

0

0

0

0

0

1

1

0

0

0

0

1

1

Addresses: Base + 0x0098, Base + 0x009A, Base + 0x009C, Base 
+ 0x009E, Base + 0x00A0, 

Access: R/W

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

0

0

0

0

0

PA

OBE

1

1

When configured as DATA[16:20], the OBE bit has no effect. When configured as GPDO, set the OBE bit to 1.

IBE

2

2

When the pad is configured as an output, set the IBE bit to 1 to show the pin state in the GPDI register. Clear the IBE bit to 0 
to reduce power consumption. When configured as GPDI, set the IBE bit to 1.

DSC

ODE

3

3

When configured as DATA[16:20], clear the ODE bit to 0.

HYS

4

4

If external master operation is enabled, clear the HYS bit to 0. 

0

0

WPE

5

5

Refer to the EBI section for weak pullup settings when configured as DATA[16:20].

WPS

5

W

RESET:

0

0

0

0

0

0

0

0

1

1

0

0

0

0

1

1

Summary of Contents for MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5565

Wang 2236 Product/Maintenance Manual preview
2236
Brand: Wang Pages: 68
NAVITAS TSE Series Installation Manual preview
TSE Series
Brand: NAVITAS Pages: 14
Mita WP3000 Manual preview
WP3000
Brand: Mita Pages: 7
YASKAWA Sigma II Series User Manual preview
Sigma II Series
Brand: YASKAWA Pages: 359
Texas Instruments TIDA-00830 Quick Start Manual preview
TIDA-00830
Brand: Texas Instruments Pages: 6
E-T-A ControlPlex CPC12 T Series User Manual preview
ControlPlex CPC12 T Series
Brand: E-T-A Pages: 30
InPlay IN1BN-DKC0-100-C0 User Manual preview
IN1BN-DKC0-100-C0
Brand: InPlay Pages: 11
DAV TECH DAT 096 Installation And Maintenance Manual preview
DAT 096
Brand: DAV TECH Pages: 22
Air Torque AT1001U Maintenance Manual preview
AT1001U
Brand: Air Torque Pages: 11
American DJ GALATIC STAR 19C User Instructions preview
GALATIC STAR 19C
Brand: American DJ Pages: 1
Cairox TSCTK-1 Series Original User Manual preview
TSCTK-1 Series
Brand: Cairox Pages: 3
Knoll MR173 Installation And Operating Instructions preview
MR173
Brand: Knoll Pages: 3
VisAccess VXS-5 Installation Instructions preview
VXS-5
Brand: VisAccess Pages: 3
roco MultiMAUS Manual preview
MultiMAUS
Brand: roco Pages: 128
Sinclair SWC-04 User Manual preview
SWC-04
Brand: Sinclair Pages: 36
eCOUNT aFLAT CRTtoLCD-71 Manual preview
aFLAT CRTtoLCD-71
Brand: eCOUNT Pages: 24
Mitsubishi AL2-2TC-ADP Installation Manual preview
AL2-2TC-ADP
Brand: Mitsubishi Pages: 2
Texmate Leopard Series Manual preview
Leopard Series
Brand: Texmate Pages: 10

Brands by name

Popular brands

Load more brands