Freescale Semiconductor MPC5565 Reference Manual Download Page 1080 | Manualshive

Page: 1080 / 1153

background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

24-87

24.14.5.1 Data Trace

This section deals with the data trace mechanism supported by the NXDM module. Data trace is
implemented via data write messaging (DWM) and data read messaging (DRM).

24.14.5.2 Data Trace Messaging (DTM)

NXDM data trace messaging is accomplished by snooping the NXDM data bus, and storing the
information for qualifying accesses (based on enabled features and matching target addresses). The
NXDM module traces all data access that meet the selected range and attributes.

NOTE

Data trace is ONLY performed on DMA accesses to the system bus.

24.14.5.3 DTM Message Formats

The NXDM block supports five types of DTM Messages — data write, data read, data write
synchronization, data read synchronization and error messages.

24.14.5.3.1

Data Write and Data Read Messages

The data write and data read messages contain the data write/read value and the address of the write/read
access, relative to the previous data trace message. Data write message and data read message information
is messaged out in the following format:

Figure 24-66. Data Write/Read Message Format

24.14.5.3.2

DTM Overflow Error Messages

An error message occurs when a new message cannot be queued due to the message queue being full. The
FIFO will discard incoming messages until it has completely emptied the queue. After it is emptied, an
error message will be queued. The error encoding will indicate which types of messages attempted to be
queued while the FIFO was being emptied.

If only a data trace message attempts to enter the queue while it is being emptied, the error message will
incorporate the data trace only error encoding (00010). If a watchpoint also attempts to be queued while
the FIFO is being emptied, then the error message will incorporate error encoding (01000).

DATA

MSB

LSB

2

3

4

U-ADDR

DSZ

SRC

5

4 bits

1

TCODE (000101 or 000110)

3 bits

1-32 bits

1-64 bits

6 bits

Max length = 109 bits; Min length = 15 bits

«
...
1078
1079
1080
1081
1082
...
»

Summary of Contents for MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5565

Brand: Samson Pages: 48

Brand: J+J Pages: 2

Brand: National Instruments Pages: 72

Brand: Mosa Pages: 28

Brand: Grosvenor Pages: 5

Brand: Velp Scientifica Pages: 24

Brand: Tapeswitch Pages: 2

Brand: AMALGAMATED INSTRUMENT Pages: 27

agility AGY-101

Brand: Fairford Pages: 127

All Sport 1600 Series

Brand: Daktronics Pages: 92

Brand: M-system Pages: 8

Brand: S&S Northern Pages: 8

Brand: Hanna Instruments Pages: 28

CompleteStat CS9B-THOA

Brand: Bard Pages: 10

Brand: Wahlberg Pages: 40

Scalar Distributed Library Controller 2.7

Brand: Quantum Pages: 324

Brand: Infineon Pages: 35

Brand: Hanna Instruments Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands