manualshive.com logo in svg

Siemens SIMODRIVE 611 universal, Function Manual

The Siemens SIMODRIVE 611 universal is a reliable and versatile product designed for various industrial applications. Unlocking its full potential is made easy with the comprehensive Function Manual available for free download at manualshive.com. Access this essential manual now, and unleash the capabilities of your Siemens SIMODRIVE 611 universal.

Share
Download
background image

6

6.16 Rotor position synchronization/rotor position identification

6-615

 Siemens AG 2005 All Rights Reserved

SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition

6.16

Rotor position synchronization/rotor position identification

Drive converters with field–orientated closed–loop control impress the
current into permanent–magnet synchronous motors to establish the
magnetic flux in the motor.
At power–on, the rotor position identification automatically determines
the absolute rotor position using the maximum of the magnetic flux.

The rotor position identification is used for:

Determining the rotor position (coarse synchronization and fine syn-
chronization)

Supports commissioning when determining the commutation angle
offset

Two techniques can be used for the rotor position identification routine:

A technique based on saturation

A technique based on movement (from SW 6.1).

The particular technique can be selected using parameter P1075.

Determining the rotor position

The rotor position identification routine automatically determines the
motor rotor position. This means that the motor encoder does not re-
quire any additional position information from the encoder (C/D track).
For linear motors, Hall sensors are not required if the limitations and
secondary conditions are maintained.

Passing–over the zero mark

As a result of the accuracy of the identification technique, the rotor
position which has been determined can be accepted at the zero for
the fine synchronization.

Encoder adjustment is not required if the rotor position identification
routine is used for coarse and fine synchronization.

I

n P1011, bit 12 (identify coarse position) is set in order that the rotor

position identification technique is initiated when powering–up the drive.
If bit 13 is set (fine position identification), a rotor position identification
is executed independently of bit 12.

Description

Coarse
synchronization

Fine
synchronization

Equivalent of 
the encoder
adjustment

Configuration,
actual value
sensing motor
encoder

6  Description of the Functions

08.02

Summary of Contents for SIMODRIVE 611 universal



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMODRIVE 611 universal

XBOX 360 Quick Manual preview
360
Brand: XBOX Pages: 2
Wave Italy IMPACT Installation, Use And Maintenance Manual preview
IMPACT
Brand: Wave Italy Pages: 16
TA Hydronics STS Technical Description preview
STS
Brand: TA Hydronics Pages: 14
Calsense ET2000e Programming Manual preview
ET2000e
Brand: Calsense Pages: 74
Salda TPC User Manual preview
TPC
Brand: Salda Pages: 16
H3C WX Series Configuration Manual preview
WX Series
Brand: H3C Pages: 69
FAAC E124 Manual preview
E124
Brand: FAAC Pages: 32
Gate Motors Q80A Quick Start Manual preview
Q80A
Brand: Gate Motors Pages: 6
Jedia JMA-5104 Operating Instructions Manual preview
JMA-5104
Brand: Jedia Pages: 12
JED Micro T470 User And Installation Manual preview
T470
Brand: JED Micro Pages: 10
JCM Technologies SESAME Rapid Installation Manual preview
SESAME
Brand: JCM Technologies Pages: 2
ZIGBEE RC-02 User Manual preview
RC-02
Brand: ZIGBEE Pages: 5
Nacon GC-200WL Instruction Booklet preview
GC-200WL
Brand: Nacon Pages: 24
NAD C 399 Addendum Sheet preview
C 399
Brand: NAD Pages: 4
NAD C388 Addendum Sheet preview
C388
Brand: NAD Pages: 4
Baier 50VA Instruction Manual preview
50VA
Brand: Baier Pages: 20
Linak TR-EM-288-SPF Quick Manual preview
TR-EM-288-SPF
Brand: Linak Pages: 2
Elfa 75-576-22 Manual preview
75-576-22
Brand: Elfa Pages: 22

Brands by name

Popular brands

Load more brands