Siemens SIMODRIVE 611 universal Function Manual Download Page 537 | Manualshive

Page: 537 / 930

background image

6

6.6

Analog inputs

6-537

Siemens AG 2005 All Rights Reserved

SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition

Table 6-53

Parameter for M

set

mode using terminal 56.x/14.x and/or terminal 24.x/20.x, continued

Parameters

No.

Effec-

tive

Units

Max.

Stan-

dard

Min.

Description

1242:8

Offset torque setpoint (open–loop torque
controlled) (SRM, ARM)

Offset force setpoint (open–loop torque con-
trolled) (SLM)

–50 000.0

0.0

50 000.0

Nm

N

Imme-
diately

This parameter value is added to the torque setpoint or force setpoint (SLM).

Note:

Thus, a pre–tensioning torque can be generated.

0620

For the torque/power reduction via terminal 24.x/20.x (refer to Chapter 6.6.4), this parameter

1243:8

For the torque/power reduction via terminal 24.x/20.x (refer to Chapter 6.6.4), this parameter
can be used to make adjustments.

1244

can be used to make adjustments.

6.6.4

Torque/power reduction via terminal 24.x/20.x

A continuous torque/power reduction (M

red

mode) is possible via ana-

log input 2 (terminal 24.x/20.x) by entering an analog voltage.

The reduction is:

In the constant torque range,
referred to the 1st torque limit (P1230)

Constant power range
referred to the first power limit (P1235)

The following characteristics can be set, as a function of parameter
P1244, using the setpoint from terminal 24.x/20.x:

Negative characteristic (P1244 = 1)

– Application

For wire breakage, the input voltage is 0 V
––> the limits for the torque/power are effective, defined with the
normalization (maximum values)
––> this case is suitable for applications which require a torque
when a fault occurs (e.g. hanging axes)

Positive characteristic (P1244 = 2)

– Application

For a wire breakage, a 0 V input voltage becomes effective
––> there is no torque/power
––> this case is suitable for applications which do not require
torque under fault/error conditions

Description

Characteristics to
reduce the
torque/power

6 Description of the Functions

01.99

! not 611ue !

«
...
535
536
537
538
539
...
»

Summary of Contents for SIMODRIVE 611 universal



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMODRIVE 611 universal

Brand: Balboa Pages: 12

Brand: Paoli Pages: 16

Brand: NEC Pages: 146

Brand: FrSky Pages: 2

Brand: Samsung Pages: 27

Brand: GBD Pages: 68

Brand: Watts Pages: 2

Brand: Hanbay Pages: 18

Brand: BabySafe Pages: 24

Brand: Danfoss Pages: 85

VLT Decentral FCD 300

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 4

VLT 6000 series

Brand: Danfoss Pages: 27

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

ADAP-KOOL AK-PC 781

Brand: Danfoss Pages: 14

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands