Siemens SIMODRIVE 611 universal Function Manual Download Page 568 | Manualshive

Page: 568 / 930

background image

6

6.8

Angular incremental encoder interface (X461, X462)

6-568

Siemens AG 2005 All Rights Reserved

SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition

An axis is moved using the ”electronic handwheel” dependent on the
direction.

The direction should be set as follows using parameter P0899[8]:

P0899[8]=0: positive and negative direction (standard)

P0899[8]=1: only in the positive direction

P0899[8]=2: only in the negative direction

Note

Angular incremental encoder pulses in the inhibited direction do not
result in the output of faults or warnings.

In the inhibited direction, only the pulses of the velocity setpoint are
cancelled. The velocity actual value must not necessarily follow the
velocity setpoint, e.g. as a result of external forces or transient
operations. As a result, motion is also possible in the direction that has
not been enabled.

The handwheel direction of rotation can be inverted as follows:

Using the input terminal function No. 75 ”Invert angular incremental
encoder input”, i.e. when the axis is stationary, the incremental posi-
tion reference value is immediately inverted with a 1 signal at the
input terminals.

”External inversion position reference value”, via parameter P0897 –
i.e. the inversion of the incremental position reference value with
P0897 = 1 – is only effective after power on.

The following actions are not possible and initiate the appropriate
faults:

If the input terminals Fct. No. 62 or control signal STW1.8 (jogging 1
ON) or Fct. No. 63 or STW1.9 (jogging 2 ON) and Fct. No. 84 or
SatzAnw.13 (activate angular incremental encoder, handwheel) are
simultaneously activated, then fault 121 is output.

If input terminal Fct. No. 72 or control signal PosStw.4 (activate cou-
pling) and Fct. No. 84 or SatzAnw.13 (activate angular incremental
encoder handwheel) are simultaneously activated, if a position refer-
ence value source is active via Parameter P0891, then fault 167 is
output.

Angular
incremental
encoder –
direction-
dependent

Angular
incremental
encoder inversion

Fault handling

6 Description of the Functions

01.99

06.04

«
...
566
567
568
569
570
...
»

Summary of Contents for SIMODRIVE 611 universal



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMODRIVE 611 universal

Brand: BADODOSECURITY Pages: 8

Brand: Yamaha Pages: 5

Brand: Yamaha Pages: 20

Brand: Yamaha Pages: 2

Brand: Reliance Foundry Pages: 3

Brand: Wesa Pages: 8

Brand: Airmar Technology Corporation Pages: 4

Brand: Motorline professional Pages: 8

Brand: Swagelok Pages: 20

Brand: V-ZUG Pages: 24

Brand: Vag Pages: 19

Brand: Carrier Pages: 86

Brand: Hoffer Pages: 57

PyroSigma Series

Brand: Calex Pages: 12

Brand: JANE Pages: 148

Brand: M-system Pages: 3

GVB-8-WP Series

Brand: Genasun Pages: 8

Brand: KELD Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands