Siemens SIMODRIVE 611 universal Function Manual Download Page 389 | Manualshive

Page: 389 / 930

background image

6

6.2

Positioning mode (P0700 = 3, from SW 2.1)

6-389

Siemens AG 2005 All Rights Reserved

SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition

6.2.4

Referencing and adjusting

In order that the ”SIMODRIVE 611 universal” drive precisely identifies
the machine zero point after power–on, the axis measuring system
must be synchronized with the machine.

This synchronization is realized when referencing incremental measur-
ing systems or adjusting absolute measuring systems.

Notice

The following functions are ineffective for axes which are either not
referenced not adjusted:

Software limit switch

Backlash compensation

Start the traversing blocks

6.2.5

Referencing for incremental measuring systems

For axes with incremental measuring systems, each time the system is
powered–up, the position reference to the machine zero point must be
established.

Synchronization is realized for a reference point approach by accepting
a specific position value at a known point of the axis.

Note

Before SW 4.1:

The encoder must be re–referenced if, for a referenced incremental
measuring system, a parameter set was changed over.

From SW 4.1:

Using P0239, the behavior for a parameter set changeover can be
set for a motor measuring system.

P0239 = 0: Behavior as before SW 4.1 (standard)

P0239 = 1: For a parameter set changeover, it is only necessary

to re–reference the encoder, if the ratio P0237/P0238
has changed.

Definitions

General
information

6 Description of the Functions

01.99

! not 611ue !

08.01

«
...
387
388
389
390
391
...
»

Summary of Contents for SIMODRIVE 611 universal



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMODRIVE 611 universal

Brand: Panasonic Pages: 16

Brand: Jands Pages: 7

Brand: hager Pages: 11

coviva Smartbox TKP100A

Brand: hager Pages: 34

Brand: Parker Pages: 28

Brand: Oceanic Pages: 11

Tissue-Tek TEC 6

Brand: Sakura Seiki Pages: 6

Brand: Ultratec Pages: 33

Brand: GADGETMONSTER Pages: 30

Brand: WAGO Pages: 16

Brand: DAQ Pages: 63

Brand: Argo-Hytos Pages: 38

Brand: Anest Iwata Pages: 8

Brand: IMG STAGELINE Pages: 14

Brand: VAT Pages: 77

Brand: Simpnic Pages: 16

Brand: Pestill Pages: 4

Brand: FEAM Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands