manualshive.com logo in svg

Siemens SIMODRIVE 611 universal, Function Manual

The Siemens SIMODRIVE 611 universal is a reliable and versatile product designed for various industrial applications. Unlocking its full potential is made easy with the comprehensive Function Manual available for free download at manualshive.com. Access this essential manual now, and unleash the capabilities of your Siemens SIMODRIVE 611 universal.

Share
Download
background image

6

6.8

Angular incremental encoder interface (X461, X462)

6-558

 Siemens AG 2005 All Rights Reserved

SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition

6.8.1

Angular incremental encoder interface as output (P0890 = 1)

The angular incremental encoder interface (X461, X462) is set as out-
put using P0890 = 1, i.e. the incremental position actual value of the
motor encoder is output via terminals A+.x/A–.x, B+.x/B–.x, R+.x/R–.x.

The encoder signals are output, depending on the encoder type, and
can still be partially manipulated (e.g. scaling or shifting, refer to Table
6-57).

Higher–level control

SIMODRIVE 611 

universal

Angular incr.
enc.
Interface
(parameterized
as angular incr.
enc. interface
P0890 = 1)

n

set

analog

– Setpoint –

– Actual value –

Table 6-57 shows for 
which encoders, which
signals are output via the
angular incremental
encoder interface, and
what can be manipulated.

n

set

analog

Angular incr.
enc.
Interface
(parameterized
as angular incr.
enc. interface
P0890 = 1)

Fig. 6-65 Angular incremental encoder interface parameterized as output

Note

If, from SW 8.1, an induction motor with TTL encoder is connected to
”SIMODRIVE 611 universal HR”, then it is not permissible that the
angular incremental encoder interface is used as output.

Description

6  Description of the Functions

01.99

! not 611ue !

06.04

Summary of Contents for SIMODRIVE 611 universal



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMODRIVE 611 universal

Danfoss 103E7 Installation & User'S Instructions preview
103E7
Brand: Danfoss Pages: 24
Samson 327 Translation Of The Original Operating Instruction preview
327
Brand: Samson Pages: 73
Lamtec BT300 BurnerTronic Quick Reference preview
BT300 BurnerTronic
Brand: Lamtec Pages: 48
Nedap WIM Installation Manual preview
WIM
Brand: Nedap Pages: 20
Eaton FC18 User Manual preview
FC18
Brand: Eaton Pages: 10
Idemia SIGMA Series Quick User Manual preview
SIGMA Series
Brand: Idemia Pages: 29
Yngri YORK Manual preview
YORK
Brand: Yngri Pages: 20
Lab.gruppen LAB.LEVEL4 Quick Start Manual preview
LAB.LEVEL4
Brand: Lab.gruppen Pages: 2
Idex Pulsafeeder MPC Vector Installation, Operation & Maintenance Manual preview
Pulsafeeder MPC Vector
Brand: Idex Pages: 114
YASKAWA Z1000 CIMR-ZU*A Series Programming Manual preview
Z1000 CIMR-ZU*A Series
Brand: YASKAWA Pages: 340
ETC Echoflex ELED2 Installation Manual preview
Echoflex ELED2
Brand: ETC Pages: 8
Texas Instruments MSP430F67681 Manual preview
MSP430F67681
Brand: Texas Instruments Pages: 27
EMS ZITON RADIO LOOP MODULE Programming Manual preview
ZITON RADIO LOOP MODULE
Brand: EMS Pages: 26
Danfoss 084B8012 Instructions Manual preview
084B8012
Brand: Danfoss Pages: 30
mikroElektronika ETH WIZ click Quick Start Manual preview
ETH WIZ click
Brand: mikroElektronika Pages: 3
Window Master WMU 831 Installation Instructions Manual preview
WMU 831
Brand: Window Master Pages: 7
Belimo LF24-SR-E US Manual preview
LF24-SR-E US
Brand: Belimo Pages: 2
Watts AMES 650GD Installation, Operation And Maintenance Manual preview
AMES 650GD
Brand: Watts Pages: 12

Brands by name

Popular brands

Load more brands