Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 580

Page: 580 / 1058

53. MLD Snooping Commands

581

53.8. show mld_snooping statistic counter



Description

This command is used to display the MLD snooping statistics counters for MLD protocol

packets that are transmitted or received by the Switching Hub since MLD snooping was

enabled.



Format

show mld_snooping statistic counter [vlan <vlan_name 32> | vlanid <vlanid_list> | ports

<portlist>]



Parameters



Restrictions

None.



Example

To display the MLD snooping statistics counters on port 1:

vlan

Specify a VLAN to be displayed.
<vlan_name 32>

Specify the VLAN name. The maximum length is 32 characters.

vlanid

Specify a list of VLANs to be displayed.
<vlanid_list>

Specify the VLAN ID list.

ports

Specify a list of ports to be displayed.
<portlist>

Specify a list of ports.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands