Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 97

Page: 97 / 1058

7. Access Control List (ACL) Commands



Parameters

profile_id

Specify the index of the access list profile.
<value 1-6>

Specify the value between 1 and 6.

profile_name

Specify the profile name.
<name 1-32>

Specify the profile name. The maximum length is 32 characters.

add access_id

Specify the index of the access list entry. The lower the access ID, the higher the priority.
auto_assign

Specify to automatically assign the access ID.

Specify a value between 1 and 256.

ethernet Specify an Ethernet access control list rule.

vlan Specify the VLAN name.

<vlan_name 32>

Specify the VLAN name. The maximum length is 32 characters.

vlanidSpecify the VLAN ID.

Specify the VLAN ID between 1 and 4094.

mask (Optional) Specify the mask.

Specify the mask.

source_mac

Specify the source MAC address.
<macaddr>

Specify the source MAC address.

mask (Optional) Specify the mask.

Specify the mask.

destination_mac

Specify the destination MAC address.
<macaddr>

Specify the destination MAC address.

mask (Optional) Specify the mask.

Specify the mask.

802.1p

Specify the value of the 802.1p priority tag.
<value 0-7>

Specify the value of the 802.1p priority tag. The priority tag ranges from 1 to
7.

ethernet_type

Specify the Ethernet type.
<hex 0x0-0xffff>

Specify the Ethernet type.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands