Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 163

Page: 163 / 1058

12. Basic IP Commands

164



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To disable the state for an interface:

12.6. show ipif



Description

This command is used to display IP interface settings.



Format

show ipif {<ipif_name 12>}



Parameters



Restrictions

None.



Example

To display IP interface settings:

all

All of the IP interfaces.

Zxxx0:admin#disable ipif petrovic1
Command: disable ipif petrovic1

Success.

Zxxx0:admin#

<ipif_name 12>

(Optional) The name of the interface.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands