manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

8.  Access Control List (ACL) Egress Command List

126

flag

(Optional) Specifies the TCP flag fields.
all

Specifies that the TCP flag field will be set to 'all'.

urg

Specifies that the TCP flag field will be set to 'urg'.

ack

Specifies that the TCP flag field will be set to 'ack'.

psh

Specifies that the TCP flag field will be set to 'psh'.

rst

Specifies that the TCP flag field will be set to 'rst'.

syn 

Specifies that the TCP flag field will be set to 'syn'.

fin

Specifies that the TCP flag field will be set to 'fin'.

udp  (Optional) Specifies that the following parameters configured will apply to the UDP           

configuration.
src_port 

Specifies the UDP source port range.
<value 0-65535>

Enter the UDP source port range value here.

mask Specifies the UDP source port mask here.

<hex 0x0-0xffff> 

Enter the UDP source port mask value here.

dst_port 

Specifies the UDP destination port range.
<value 0-65535> 

Enter the UDP destination port range value here.

mask  Specifies the UDP destination port mask here.

<hex 0x0-0xffff> 

Enter the UDP destination port mask value here.

protocol_id 

(Optional) Specifies that the rule will apply to the value of IP protocol ID traffic.
<value 0-255> 

Enter the protocol ID used here. This value must be between 0 and 255.

user_define

(Optional) Specifies that the rule will apply to the IP protocol ID and that the mask               
options behind the IP header, which has a length of 20 bytes.
<hex 0x0-0xffffffff>

Enter the user-defined mask value here.

mask  Specifies the user-defined mask here.

<hex 0x0-0xffffffff> 

Enter the user-defined mask value here.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

H3C S5800-EI Series Installation Manual preview
S5800-EI Series
Brand: H3C Pages: 61
BeeSecure BEE-REPEATER Quick Start Manual preview
BEE-REPEATER
Brand: BeeSecure Pages: 35
Manhattan 160605 Quick Start Manual preview
160605
Brand: Manhattan Pages: 2
Abseco AFI-2M0S1B Installation Manual preview
AFI-2M0S1B
Brand: Abseco Pages: 10
Harman AMX ENOVA DVX-3250HD-SP Instruction Manual preview
AMX ENOVA DVX-3250HD-SP
Brand: Harman Pages: 119
Clas Ohlson EMT1700P Manual preview
EMT1700P
Brand: Clas Ohlson Pages: 5
Ross OpenGear DSS-8224 User Manual preview
OpenGear DSS-8224
Brand: Ross Pages: 47
Versitron SG70660M Installation Manual preview
SG70660M
Brand: Versitron Pages: 46
Hama 5-Port Gigabit Switch 1000 Mbps User Manual preview
5-Port Gigabit Switch 1000 Mbps
Brand: Hama Pages: 2
WELLTECH WPoE-2426 User Manual preview
WPoE-2426
Brand: WELLTECH Pages: 280
Ruby Tech ES-1126C/D Specifications preview
ES-1126C/D
Brand: Ruby Tech Pages: 2
Smartwares SH8-90604 Manual preview
SH8-90604
Brand: Smartwares Pages: 44
CONCORD CS4WH20B4KS-A Manual preview
CS4WH20B4KS-A
Brand: CONCORD Pages: 18
Gefen EXT-DVI-444DL User Manual preview
EXT-DVI-444DL
Brand: Gefen Pages: 20
Rolls ABY32 Owner'S Manual preview
ABY32
Brand: Rolls Pages: 2
Field Controls 46114900 Manual preview
46114900
Brand: Field Controls Pages: 4
Raritan Dominion KX II Quick Setup Manual preview
Dominion KX II
Brand: Raritan Pages: 7
Cable Electronics e labs CAT5TX/RX Specification Sheet preview
e labs CAT5TX/RX
Brand: Cable Electronics Pages: 2

Brands by name

Popular brands

Load more brands