manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

91.  System Log Lists    

1037

91.18.

#

Serverity

Log message / Explanation

1

Informational

OSPF interface <intf-name> changed state to [Up | Down] 

OSPF interface link state changed.

2

Informational

OSPF protocol on interface <intf-name> changed state to 

[Enabled | Disabled] 

OSPF interface administrator state changed.

3

Informational

OSPF interface <intf-name> changed from area <area-id> to 

area <area-id>

One OSPF interface changed from one area to another.

4

notice

OSPF nbr <nbr-id> on interface <intf-name> changed state 

from Loading to Full

One OSPF neighbor state changed from Loading to Full.

5

notice

OSPF nbr <nbr-id> on interface <intf-name> changed state 

from Full to Down

One OSPF neighbor state changed from Full to Down.

6

notice

OSPF nbr <nbr-id> on interface <intf-name> dead timer expired 

One OSPF neighbor state’s dead timer expired.

7

notice

OSPF nbr <nbr-id> on virtual link changed state from Loading 

to Full

One OSPF virtual neighbor state changed from Loading to Full.

8

notice

OSPF nbr <nbr-id> on virtual link changed state from Full to 

Down

One OSPF virtual neighbor state changed from Full to Down.

9

Informational

OSPF router ID changed to <router-id>

OSPF router ID was changed.

10

Informational

OSPF state changed to Enabled

Enable OSPF.

11

Informational

OSPF state changed to Disabled

Disable OSPF.

OSPFv2

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

Accedian Skylight LX Installation Manual preview
Skylight LX
Brand: Accedian Pages: 2
Datavideo DAC-10 Quick Setup preview
DAC-10
Brand: Datavideo Pages: 2
Jabra Link 950 USB-A How Do preview
Link 950 USB-A
Brand: Jabra Pages: 4
Jabra LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES Datasheet preview
LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES
Brand: Jabra Pages: 2
JB Systems Light SW-416 Operation Manual preview
SW-416
Brand: JB Systems Light Pages: 15
H3C S5800-EI Series Installation Manual preview
S5800-EI Series
Brand: H3C Pages: 61
PRO SIGNAL PSG3450 Manual preview
PSG3450
Brand: PRO SIGNAL Pages: 5
netvox ZigBee Z815B User Manual preview
ZigBee Z815B
Brand: netvox Pages: 14
AMAV VS81 Installation And Operation Manual preview
VS81
Brand: AMAV Pages: 8
UNIARCH SW-2106-P User Manual preview
SW-2106-P
Brand: UNIARCH Pages: 6
AMX AVS-OCT-4832-117 Product View preview
AVS-OCT-4832-117
Brand: AMX Pages: 1
IOGear GCS1808H Quick Start Manual preview
GCS1808H
Brand: IOGear Pages: 12
Wantec 2wIP-E-S-TW Installation Manual preview
2wIP-E-S-TW
Brand: Wantec Pages: 4
3onedata ICS5400PTP-12GT12GS4XS Installation preview
ICS5400PTP-12GT12GS4XS
Brand: 3onedata Pages: 3
NETGEAR GS305Pv2 Installation Manual preview
GS305Pv2
Brand: NETGEAR Pages: 2
AJAX Ajax-hub User Manual preview
Ajax-hub
Brand: AJAX Pages: 23
J-Tech Digital JTD-3004 User Manual preview
JTD-3004
Brand: J-Tech Digital Pages: 13
Kramer VS-3232A User Manual preview
VS-3232A
Brand: Kramer Pages: 70

Brands by name

Popular brands

Load more brands